Jump to content
SAU Community

Recommended Posts

Yes thats the rev range......the reason it works sometimes and not others is because it is binding up. It feels like you have 2 boost settings does it not?

Its the rear bearing failing, they get hot and fill with burnt oily crap then flog out. Ive got a photo of the bearing, I caught mine early.

post-63525-1252680737_thumb.jpg

  • 2 weeks later...
  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Yes thats the rev range......the reason it works sometimes and not others is because it is binding up. It feels like you have 2 boost settings does it not?

Sorry mate been busy....

Yeah sometimes! On ocassion it seems to hold back for a second then climb again but others its sweet. It has me stumped. Will have to have a look at the rear bearing as well.

When you initally checked the turbo when it first started happening, was there any signs of shaft play?

Edited by dozzer
Its the rear bearing failing, they get hot and fill with burnt oily crap then flog out. Ive got a photo of the bearing, I caught mine early.

which rear bearing is it? a driveshaft bearing or a tailshaft bearing?

how did you go abouts checking it to make sure thats what it was?

cheers mate.

which rear bearing is it? a driveshaft bearing or a tailshaft bearing?

how did you go abouts checking it to make sure thats what it was?

cheers mate.

that photo is of the Turbo rear bearing, not the Drive shaft or tail shaft.

It's a big job to check it on the car......just drive it till it fails.....car is still drivable without boost.

Yeah but no fun without boost!!!

Thanks for your help guys. I have some warranty left on my car so ill have to do a bit of research and see if i can make a claim.

Yeah but no fun without boost!!!

Thanks for your help guys. I have some warranty left on my car so ill have to do a bit of research and see if i can make a claim.

I looked into it but they only covered $750 for turbo and they wanted $2,500 labor just to remove and refit. Bugger that.

funny that

i still got the noise after turbo replacement..

Danny, there are three distinct noises my turbo made.

First is the suction noise, gentle and builds up to boost.

Second is the bearing whine, Mine doesnt have this at all now due to not having ball bearings. This will get louder as the bearings start to wear, and other than running good oil and changing it often theres not much you can do as eventually all ball bearings fail. They dont like heat or high revs....

Third noise I heard was a gentle metalic scraping noise. This was the thrust bearing wearing down to the point where the compressor wheel was rubbing on the housing. Again, not much you can do, they are a wearing part and the more boost you run, the quicker the thrust bearing will wear.

Which noise are you hearing?

And Cam, you stay out of it, ok? They arent the only ones.... :D

Edited by scotty nm35
  • 1 month later...

funny that

i still got the noise after turbo replacement..

Hey Danny

I just picked up my M35 today and got it registered!

Anyway I noticed the exact same noise.

only seems to happen at max torque around 3-3500 k and not on full throttle.

could it be the attessa kicking in? Does the attessa make a noise when engaging front diff?

My other theory is it's slipping in between gearchanges but havent driven it enough to really tell.

third noise

but it's gone now

hey william yeah thats wat i sounds like

but it's nothing to do with the sussy or anything

as scotty said bearing noise on the turbo

then again i dont have that noise no more

Bugger

Just went for another spirited drive... man starting to love it!

I think the noise is more like a uuurrrggghh and seems to do it between gear changes

under load. Could my auto tranny have a problem?

using the triptronic it takes ages to change gears! I'll change up at 4k and it will rev to 7k before changing!

nah his car is stock, wil when i drove it it sounded fine to me. i didnt push it THAT hard, but it was enough to get the normal sounds out of it.

my car has a weird exhaust leak under the driver. its possible yours has a similar problem.

also, check the oil and change it if it looks dirty. you dont have THAT many ks on the car so all should be well

I thought i was having problems the other day. i had a grinding noise kinda.. very faint..

it however ended up bieng the A/c.. thank god! i am not ready for the highflow or my exhaust..

Hmm

maybe i'll try it without the a/c on and see if it still makes the noise...

Any recommendations for auto trans service? If i take it to nissan what model should I say the car is similar to?

Hmm

maybe i'll try it without the a/c on and see if it still makes the noise...

Any recommendations for auto trans service? If i take it to nissan what model should I say the car is similar to?

You shouldn't have to. It clearly states to use Matic J on the dipstick, so they should be ok.

Edited by iamhe77

just to close this off.

Took my car to Nissan Osborne Park today. The noise was happening around the 4k rpm in almost any gear at half throttle.

The mechanic found the turbo intake pipe or some pipe near the turbo was rubbing hard up against the chassis, i'm not sure exact details but they've re-adjusted it.

Auto service (the fluid in there was looking a bit dark)- $330

Throttle body clean (recommended by them) - $135

Diagnose and fix that problem - $70

Replace some cracked belts - ~$120

$700 odd later and hopefully she'll be like new. Will report after I have a drive.

Funny watching one mechanic come and look at the car and he's like 'what's that? Is that an import???'

Altogether they were pretty inquisitive about the car, finding out whether it would hook up to their diagnostics, finding out what belts fit etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...