Jump to content
SAU Community

Recommended Posts

hey marko.

looks like ur a new member :D welcome to skylines australia :D

ok now you need to reset the ecu if u change the o2 sensor. to reset ecu just disconnect the battery and let leave it for a couple of minutes to discharge. you cud press down on the brake as well to discharge whatever is left. once done reconnect you battery and away you go ;)

Edited by zerotohundred
Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4623122
Share on other sites

hey marko.

looks like ur a new member ;) welcome to skylines australia :D

ok now you need to reset the ecu if u change the o2 sensor. to reset ecu just disconnect the battery and let leave it for a couple of minutes to discharge. you cud press down on the brake as well to discharge whatever is left. once done reconnect you battery and away you go :)

^^ what he said :D

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4623144
Share on other sites

Pffft...I still can't believe you guys would go into so much trouble to reset the ECU.

The proper way to do it according to a NISSAN ECR33 Service Manual is this.

1.On the right hand side just under your steering wheel is a fuse box cover. Pull it off. You will see a set of fuses and some Wiring Looms.

The one we'll need looks like this, it is not connected to anything, this is your diagnostic plug that NISSAN uses to find faults.

post-47546-1243511881_thumb.jpg

2.Now grab a piece of wire, bout .5mm-1mm in diameter, you need atleast 10cm and splice the two ends off like this.

post-47546-1243512015_thumb.jpg

3.Now we're going to short out 2 (two) of these pins, which will reset the ECU in this process.

-Turn the Ignition onto "ON", within the next 10 seconds you need to...

-Place one end of the wire into the Bottom Left Pin. "YES" put it in there...you won't get a shock.

-Place the other end of the wire in the Pin right next to it....

LIKE THIS

post-47546-1243512292_thumb.jpg

Your engine light should Flash 5 (five) times SLOW and 5 (five) times FAST.

CONGRATS...ECU RESET!!!!

It does sound complicated, but it is EASY AS!

Any questions..feel free to ask!

Also, you will need to go for a spirited drive for the ECU to correct AFR's. Atleast 3 to 4 0-100km/h runs.

Fuel is not changed, as it uses standard fuel map, but rather adjusts the Air coming in.

It will fine tune itself over a period of days.

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4623223
Share on other sites

hello again!

i swapped the o2 sensor over the weekend as well as the full service was done on the car. took it yesterday for easy drive around, i used almost half of the fuel tank and done 190 kms which is much more than what i did before this!

only cost me $109 for the NGK o2 sensor from Autobarn!!!

Thanks for the help gentlemen!!!

cheers

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4633800
Share on other sites

so umm .. changing the o2 sensor without resetting ECU would not do much good eh ? Because I have a remapped ECU with a special daughterboard installed ... would resetting the ECU make me lose my tune ie. AFRs and timing set by the tuner, when the ecu was remapped ??

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4633963
Share on other sites

so umm .. changing the o2 sensor without resetting ECU would not do much good eh ? Because I have a remapped ECU with a special daughterboard installed ... would resetting the ECU make me lose my tune ie. AFRs and timing set by the tuner, when the ecu was remapped ??

Tune is stored in read only memory, no way to undo it unless you pull the ECU apart and physically rip that chip out

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4634261
Share on other sites

Tune is stored in read only memory, no way to undo it unless you pull the ECU apart and physically rip that chip out

Oh cool, Good thing i read this before i started a new topic. I got a tuned ecu and wanna reset it before i run it in my car. Will give it it a go tonight.

Cheers

Edited by Benzino33
Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4634423
Share on other sites

pretty sure they are the same. the very best way to do it is to buy a consult cable and reset it that way. it actually costs money to do but gives you a valuable piece of equipment that allows you to also monitor things like the AFM o2 sensor, etc as well as read fault codes without having to count a flashing light

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4635914
Share on other sites

any free software that works with the usb consult cable ?? I'm thinking of getting a Nisture chip down the road so I might just get this usb consult from http://www.plmsdevelopments.com They sell the Nistune software too but right now I don't need it as I'm not getting the car retuned just yet..

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4636380
Share on other sites

  • 3 weeks later...
CONGRATS...ECU RESET!!!!

Any questions..feel free to ask!

the only question i have is "are you sure". i know what you've described is how you get the fault codes, but ive never heard it resets the learned parameters in the ECU? where did you read that? (i guess i should look in the service manual myself).

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4675805
Share on other sites

This ECU resetting logic is a bit askew in my opinion...

Why are we resetting the ECU? It doesn't store an infinite amount of driving patterns - with most ECUs the existing patterns should be overlapped after about 30 ignition starts anyway. It's certainly not necessary for installing a new oxygen sensor. My car is evidence of this; economy went from 250km per 50 litres to about 380 after installing my new sensor. Are we also assuming that the new oxygen sensor is not going to send voltage readings of its own, and that the ECU is infact going to reference the old sensor's readings instead? Kind of defeats the point of having an oxygen sensor in the first place don't you think!

Also, after resetting the ECU, full throttle 0-100km/h runs will in no way be beneficial - your standard driving style will overtake this in about 30 ignition starts anyway.

The only time I would reset an ECU is to clear fault codes or if I had idle troubles which the ECU can maintain even after driving pattern overlap. All this said, whenever I am working on engine bay wiring I disconnect the battery (which will automatically reset the ECU after 20 minutes anyway). However, oxygen sensor is just plug and play installation so you will be safe from electric shock.

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4676078
Share on other sites

Pffft...I still can't believe you guys would go into so much trouble to reset the ECU.

The proper way to do it according to a NISSAN ECR33 Service Manual is this.

Oh the irony ..how's doing ALL THAT less trouble than disconnecting the battery for a few mins ? Heh.

Anyway, changed my o2 sensor with a genuine Nissan one and got zero improvement. Changed the AFM too. I must be the only person on SAU who's had ZERO improvement after changing the o2 sensor. I do have a JJR dump pipe ..could that have something to do with it? Maybe the o2 sensor just isn't able to give correct readings? I read somewhere before that some people had problems with the JJR dump pipe..

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4676658
Share on other sites

economy hadn't changed after remap ..plus the remap made the AFRs leaner as it was running rich from factory as they all do, so you'd expect that would have given me a better economy on its own but nup..

The factory o2 sensor was not dead but it was time to replace it anyway. Just surprised neither new o2 sensor nor AFM made any difference, that's all.

Link to comment
https://www.sau.com.au/forums/topic/271900-reset-ecu/#findComment-4676986
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...