Jump to content
SAU Community

Pics Of The 1st National Uk Stagea Meet

RSVFOURUK
 Share

Recommended Posts

RSVFOURUK Collaborator

RSVFOURUK

Posted
Posted

Some pics of the first UK stagea owners club first national meet.

I do appreciate that 13 Stageas in one place may not be unusual downunder but please bear in mind that there were probably less than that actually in the UK 18 months ago.

The meet lasted two days and the longest distance travelled was a round trip of just under 750 miles.

Notionalmeetphotos010.jpg

Notionalmeetphotos016.jpg

Photo05231417_4.jpg STAGEA ON LPG

02032007374.jpg 260 RS

DARKPIC.jpg

Photo05231417.jpg

dscf5201.jpg RENIK GT FOUR

Cimg4298.jpg

02032007368.jpg

02032007366.jpg

02032007371.jpg

02032007369.jpg

WINNER OF "CAR YOU WOULD MOST LIKE TO STEAL"

1stAnnaulNSOCmeet006.jpg

dscf5177.jpg

1stAnnaulNSOCmeet004.jpg

ENGINE.jpg

RSVFOURUK Collaborator

RSVFOURUK

Posted
  • Author
Posted
hahah very cool!!

i hope ours turns out well also!

no M35s over there yet??

We have a ten year rule which means that we are only just getting round to importing series 2 cars . M35s will be a long way off.

Bis-e Bee Mentor

Bis-e Bee

Posted
Posted

Wait until you see the shots of our sydney turn-out on the 7th of June :yes:

I think we have 20 coming along, a mixture of WC34's and M35's, pics will be posted up shortly thereafter.

RSVFOURUK Collaborator

RSVFOURUK

Posted
  • Author
Posted (edited)

Thanks for showing interest

A few answers

the carbon fibre air diversion plate on the green S1...... gimme gimme gimme! were can i get one?

I ordered it from japan was actually supplied by garage defend and was made as a special from a pattern they had - first fit was rubbish but after a few hours help its fine.

Awesome! That green Stag is hot! Genuine (Nismo) 260RS or conversion? 6 spot front calipers..... nice.

It started off life a an RS Four (but so did the autechs),The conversion was done by major japanese tuning house inc genuine Nismo bodykit . Imported 2 years ago it now has forged tomei engine approx 600 bhp , most handling mods you can do and recaro interior.

Does the one with the RIPS number plate have a 1000hp RIPS RB30?

No but it is the tow car for a RB30 drag R34GTR built by RIPS that runs reguarly at the UK drag meets

Edited by RSVFOURUK
iamhe77 Grand Master

iamhe77

Posted
Posted (edited)
what you think Cam ?

we get one going here ? a few vic owners need a few kicks up the bum to get out.

seems like most use it as a family car, so somthing family orientated ? to keep the women happy haha

I would TJ, but I probably wouldn't turn up :thumbsup:

Edited by iamhe77

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • MBS206
      Starter motor replacment teeth count.

      By MBS206 · Posted

      I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...