Jump to content
SAU Community

M35 Manual

RBPOWA-(TJ)
 Share

Recommended Posts

Paramour Proficient

Paramour

Posted
Posted
i think its been determined that they cant be complied as yet!

however i think someone is working on it.........

True, But I very very much like the seats. . would look great in my car. . . .as would that 6 Speed manual. .

Link to comment
https://www.sau.com.au/forums/topic/274122-m35-manual/#findComment-4648102
Share on other sites
Bis-e Bee Mentor

Bis-e Bee

Posted
Posted
WTF.................. :mad:

Why does this stuff keep getting listed? Just to stuff up the innocent.

I agree, it's extremely deceptive and I'm sure it will catch more people up if they don't do the research before initiating the purchase process.

Do these places want to be taken to court or what?

Link to comment
https://www.sau.com.au/forums/topic/274122-m35-manual/#findComment-4648711
Share on other sites
iamhe77 Grand Master

iamhe77

Posted
Posted
i think its been determined that they cant be complied as yet!

however i think someone is working on it.........

Give it 3 months or so and it should cover all models, not just RWD RX (which is the car going through compliance), but all AWD models as well as the 350s.

Will be sticking with my 250t though.

Nobody told me (since I wasn't there), was the 350RX brought to the meet on the weekend?

Link to comment
https://www.sau.com.au/forums/topic/274122-m35-manual/#findComment-4649221
Share on other sites
iamhe77 Grand Master

iamhe77

Posted
Posted
Does this mean that there is light at the end of the tunnel for Muz and the other guys with 04MY turbos? Or are they still buggered?

Still buggered unfortunately.

easy rule is

VQ25DET is ok up until Oct 2003

VQ35DE will be fine from 2004 - end of production.

Link to comment
https://www.sau.com.au/forums/topic/274122-m35-manual/#findComment-4649416
Share on other sites
mxfly Veteran

mxfly

Posted
Posted

I've had a 350Z with the VQ35DE motor in it. What can I say, it's a lovely engine. The thing that I'm most impressed with is the sheer torque you get as soon as you floor it and it's that initial feeling that had put a smile on my face. Sure we all know that it takes a bit more time to get a VQ25DET to sing, and when she sings, she does it loud and proud. But really, it's that precious second or two that can make the difference.

What I'm not impressed with the DE engine is how it responds to your basic mods. Pretty much you need to fork out a small fortune to really make it into a real thoroughbred. I did so much to the 350 it wasnt funny, and in the end, I gave up and decided that a forced induction car was the way to go.

With the Stag, a simple dump/front pipe change with a high flow cat has already made a big difference. I cant wait till my cat-back arrives and see how much better she goes.

Link to comment
https://www.sau.com.au/forums/topic/274122-m35-manual/#findComment-4649918
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...