Jump to content
SAU Community

Recommended Posts

The ATTESA system used in the GTR and Stageas is mostly all the same - but with tweaks here and there to suit the vehicle and its intended use. I think mechanically it is more or less the same and the way it works is also more or less the same, but the AWD computer will be set up differently to suit the car.

And yes it is true the system will read many different inputs (100x per second) - throttle position, ABS sensors (to determine lost traction), and longitudinal and latitudinal g-force sensors, to determine the weight-shift of the car, sideways and front-back g-forces etc and basically the rule is: If ANY wheelspin (or POTENTIAL for wheelspin) is detected at any wheel, the system will direct torque away from that wheel. The torque split is completely variable - from up to ~95% rear to about 50% front 50% rear - or it can be anywhere in between - as the computer sees necessary.

Its one of the most advanced AWD systems in the world, and works extremely well. It is however not designed for heavy offroad use or situations where you are in AWD constantly (ie. all day). The 4x4 Nissans do still use a form of ATTESA but they also feature the usual 4WD diffs etc to support 4WD mode. On stageas and GTR's the system relies on clutch packs which will wear out if used all the time. Its more like a backup system to ensure maximum traction on the road - and it is more than capable of achieving this.

My favourite thing about ATTESA is that its RWD most of the time, so you get the fuel economy/drivetrain losses of a RWD car (in theory) when just cruising around, but the safety and traction of AWD when you need it. In my opinion its much better than full time AWD systems like mitsubishi and subaru, however those systems have their advantages as well (just that those advantages usually manifest themselves on a rally circuit, not on the road).

Actually this is a complete can of worms with some manufacturers claiming full time AWD when they don't have it...

Subaru actually have 4 different AWD systems, depending on engine and transmission options. I won't go into too much detail, but only manual Subarus actually have full time AWD. All the automatics have a clutch pack replacing the centre active diff, or viscus coupling, of the manual versions. That makes them part time AWD, same as our Nissans.

But hey, when have marketing guys ever worried about the truth...

The ATTESA system used in the GTR and Stageas is mostly all the same - but with tweaks here and there to suit the vehicle and its intended use. I think mechanically it is more or less the same and the way it works is also more or less the same, but the AWD computer will be set up differently to suit the car.

And yes it is true the system will read many different inputs (100x per second) - throttle position, ABS sensors (to determine lost traction), and longitudinal and latitudinal g-force sensors, to determine the weight-shift of the car, sideways and front-back g-forces etc and basically the rule is: If ANY wheelspin (or POTENTIAL for wheelspin) is detected at any wheel, the system will direct torque away from that wheel. The torque split is completely variable - from up to ~95% rear to about 50% front 50% rear - or it can be anywhere in between - as the computer sees necessary.

Its one of the most advanced AWD systems in the world, and works extremely well. It is however not designed for heavy offroad use or situations where you are in AWD constantly (ie. all day). The 4x4 Nissans do still use a form of ATTESA but they also feature the usual 4WD diffs etc to support 4WD mode. On stageas and GTR's the system relies on clutch packs which will wear out if used all the time. Its more like a backup system to ensure maximum traction on the road - and it is more than capable of achieving this.

My favourite thing about ATTESA is that its RWD most of the time, so you get the fuel economy/drivetrain losses of a RWD car (in theory) when just cruising around, but the safety and traction of AWD when you need it. In my opinion its much better than full time AWD systems like mitsubishi and subaru, however those systems have their advantages as well (just that those advantages usually manifest themselves on a rally circuit, not on the road).

I hate that about carsales and most online car websites. when i was looking for a Legnum or stagea or anything really

most dickheads say the car is a manual when its a damn auto.. really annoying when your trying to find just a manual car..

The ATTESA system used in the GTR and Stageas is mostly all the same - but with tweaks here and there to suit the vehicle and its intended use. I think mechanically it is more or less the same and the way it works is also more or less the same, but the AWD computer will be set up differently to suit the car.

And yes it is true the system will read many different inputs (100x per second) - throttle position, ABS sensors (to determine lost traction), and longitudinal and latitudinal g-force sensors, to determine the weight-shift of the car, sideways and front-back g-forces etc and basically the rule is: If ANY wheelspin (or POTENTIAL for wheelspin) is detected at any wheel, the system will direct torque away from that wheel. The torque split is completely variable - from up to ~95% rear to about 50% front 50% rear - or it can be anywhere in between - as the computer sees necessary.

Its one of the most advanced AWD systems in the world, and works extremely well. It is however not designed for heavy offroad use or situations where you are in AWD constantly (ie. all day). The 4x4 Nissans do still use a form of ATTESA but they also feature the usual 4WD diffs etc to support 4WD mode. On stageas and GTR's the system relies on clutch packs which will wear out if used all the time. Its more like a backup system to ensure maximum traction on the road - and it is more than capable of achieving this.

My favourite thing about ATTESA is that its RWD most of the time, so you get the fuel economy/drivetrain losses of a RWD car (in theory) when just cruising around, but the safety and traction of AWD when you need it. In my opinion its much better than full time AWD systems like mitsubishi and subaru, however those systems have their advantages as well (just that those advantages usually manifest themselves on a rally circuit, not on the road).

R32GTR N1's don't have ABS (or ABS sensors), but they still have ATTESA. Personally I have never seen any 4WD response from wheelspin, it's all about throttle position, plus longitudinal and lateral G forces. R32's will go zero front torque split, R33/34's always have some drive to the front. As long as you keep the oil temperature under control, the ATTESA will handle a full day in 4WD. The clutch pack is wet, so not prone to the wear that a dry clutch gets. There is an argument that says a 50/50 torque split will actually wear the clutch pack less than 5/95. The less slip there is the lower the friction wear and 50/50 has zero slip so zero wear. The only problem with 50/50 is the front diff is so much smaller than the rear one and it simply won't take the load. Yes, I have broken the front diff in the Stagea.

Personally I think a RWD biased 4WD would make a much better rally car than a FWD biased 4WD, for the very same reasons it makes an ATTESA equipped circuit race car the best of the 4WD systems.

Cheers

Gary

AWD harder to get off the line...? What are you smoking mate? Clearly would be your tyres if ur rwd :) the awd is super easy to launch HARD

I think what he might mean is that the optimal AWD launch has a small amount of wheelspin, which can be difficult to achieve. I know with my m35, a zero wheelspin standing start (stalled against the torque converter) is not nearly as fast as one with even a small amount of wheelspin (also stalled against the converter)

Thanks to Andy and Jetwreck for the correct launch procedure! :thumbsup:

Actually this is a complete can of worms with some manufacturers claiming full time AWD when they don't have it...

Subaru actually have 4 different AWD systems, depending on engine and transmission options. I won't go into too much detail, but only manual Subarus actually have full time AWD. All the automatics have a clutch pack replacing the centre active diff, or viscus coupling, of the manual versions. That makes them part time AWD, same as our Nissans.

But hey, when have marketing guys ever worried about the truth...

hmm didn't know that - interesting. Either way the subaru system still would not be computer controlled to the degree our nissans are, allowing the torque split to vary anywhere from ~95% rear to 50-50 depending on circumstances. As I understand it (and I could be wrong), the wrx's and evo's have only a couple of preset torque split settings, that are mostly handled mechanically.

As for the AWD vs RWD thing, cars that are RWD only are a tad lighter - which in my opinion is the ONLY benefit to RWD. There are other benefits, slightly quicker, lower fuel consumption - but these are due to the weight difference also.

If you were to compare a RWD and AWD stagea with the same weight (ie. remove the front tailshaft on the AWD), the AWD is quicker down the 1/4 mile. Something to do with the AWD launch compared to RWD. Also the more power the car has, the more this swings even more in favour of AWD...

However the above was only done by someone on here with a s1 or s2. Not sure if the same holds true for the M35.

I agree getting an M35 off the line quickly is no easy task. Not sure if its just gearing or if the torque converter bogs down or what...

yes the correct one demonstrated with my car several times lol poor car!

Haha, I thought I was doing well when I stalled mine up and let fly at about 2500rpm, then the guys told me to hold out until the rear wheels start to turn... Biiiig difference!

Note*, All undertaken on closed private roads, street drag racing is naughty... DON'T DO IT!

yeah i didnt do it on the street either later that night. but it so happens i was 'parked' next to a taxi that was creeping up on me. i used this trick and shot out of the smoke.

im guessing its VERY bad for the atessa system as its slipping the clutches a lot.........

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...