Jump to content
SAU Community

Recommended Posts

I've just tried some Carbotech XP12 pads (for track work) and to be honest i wasnt overly impressed. Plus they squeal like there is no tomorrow (after a few days of light road use, like most track pads i guess) and it's a major PITA - so i've just put the stocker pads back on (super quiet again, thank god).

Anyway has anyone priced the stocker pads? From Nissan it's probably a bloody fortune, so i am not going to bother asking. But, perhaps someone has sourced them elsewhere? They are Brembo pads right?

Link to comment
https://www.sau.com.au/forums/topic/274657-r35-stocker-brake-pads/
Share on other sites

you're right, they are a fortune I can't remember exactly but it was around $1000 per axle set. look at endless or project mu. they both make great pads and should be more reasonable $$ wise. they do everything from nice quiet, low dust street pads to dusty as fk, hard when cold, agressive, 800C track pads.

that would be about right for one axle set. ie both front calipers (4 pads total). they never sell just 1 calipers worth and PMU sometimes offer full sets too (ie all pads front and rear, but $600 would be a bargain for a 35).

I picked up some Ferodo DS2500 pads for the front end yesterday, $495.

Also got some new AP rotors for $825ea too, curved slots.

I think this combo (Ferodo pads + AP rotors) will be very close to stocker setup, with the discs certainly better, but we'll see.

Out of interest, has anyone got a price from Nissan on stocker rotors or pads yet?

I assume it will be in the order of 2x the cost? - i am not even going to ask!

I picked up some Ferodo DS2500 pads for the front end yesterday, $495.

Also got some new AP rotors for $825ea too, curved slots.

I think this combo (Ferodo pads + AP rotors) will be very close to stocker setup, with the discs certainly better, but we'll see.

Out of interest, has anyone got a price from Nissan on stocker rotors or pads yet?

I assume it will be in the order of 2x the cost? - i am not even going to ask!

How are you? I hope all is well. I hope you are sitting down when you hear the OEM brake prices...OEM pads are $725 USD for front and $483 USD for the rear. The rotors (front or rear) are $1081 USD. Crazy expensive!

We offer a 'track brake package' with front and rear XP12 pads (noisy but they bite well...we can also exchange these for any other pad we offer such as Ferodo, etc.), front and rear AP Racing J-hook rotors, T1R V2 stainless steel braided brake lines, and 2x bottles of Motul RBF600 fluid for $3000 USD, with international orders getting a $75 credit toward shipping costs:

https://www.speedforsale.com/nissangtrparts...jjgv0cp0gfi5g94

Duncan

Front pads about $2000 and the rotors about $1700 each for gen brem, I mean nissan. :)

That's a pity they are so expensive. I actually liked the stocker pad/rotor combination, better than i thought it would be anyway, even for the circuit i found them fine. Since i've used aftermarket pads the stocker rotors have started to crack though. Higher friction & more heat, to be expected i suppose.

Thanks for the prices guys, hopefully the price for the stocker parts will come down in future.

  • 1 month later...
I found a set of Project MU street spec pads for about $600. Does this sound right for a front set (both sides) or just one side?

Hi Priestley,

Which model of Project Mu pads were you quoted $600 for ? Was that price for front and rear pads (ie all 4 corners of the car) or front pads only ?

Project Mu makes 3 models of street / sports pads for the R35 - the TYPE NS, B-SPEC and the TYPE HC+.

Australian prices for the R35 for Type NS front pads is AU$390. Rear pads for the R35 start at AU$249 for the NS pads.

So if you were quoted $600 for NS front and NS rear pads that's about $39 below standard Australian pricing.

We have a page on our website explaining the differences between each Project Mu pad compound available for the R35 (street / sports and competition pads, with temperature and Friction Coefficient specs) here ...

http://www.tunersgroup.com/Online_Store/r35_pads.html

- The Tuners Group

FWIW guys i have been using Ferodo DS2500 pads, about $490 (fronts) and $440 (rears) - i think these are the closest to stocker pads you will find. I've run them at the track a few times are they are very comparable to stocker performance, progressive feel and noise (not really squeaky at all). Send me a PM if you want a contact to buy these.

  • 4 months later...

Just in case you need the parts #'s here are some I have parted out with. I know this is an old thread

also here are the caliper dust boot part #'s

Front caliper is a 6piston.

Front 20.9716.01 F

Rear is a 4 piston caliper. ® 20.9717.07

Dust boots PN # 20-4872-41

Front:(dia.)

20487244 = 36mm

20487243 = 34mm

20487241 = 30mm

Rear:

20487243 = 34mm

20487241 = 30mm

DSCN5240.jpg

Edited by racer98
  • 1 month later...
  • 1 month later...

thread mining again.

What have been peoples experiences with R35 pads?

I have tried Carbotech xp12's (great bite but squealed like a cop on the street) DS2500's (about the same as stocker pads) Hawk's (did not sweep the entire rotor, 10mm less!) and MX72's (not as much bite as the xp12's but virtually squeal free on the street, and kind to rotors).

Anyone tried the project mu HC+ in their r35? if so, did they squeal? how did they perform?

they seem "cheap" about $800 for a full set.

  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...

wow those nissan prices are criminal.

Anyway i have been using Endless ccRg the last couple of track days; they seem to have the street manners of the mx72's but with more bite. They feel awesome. I think about $700 to $800 (for the fronts AND backs, yes total cost for four corners)

No squeal yet.

I think they work up to about 800*c so less fade too.

Edited by LSX-438

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...