Jump to content
SAU Community

Recommended Posts

HI all, I don't get on the forums much these days, but I thought I'd share am easy way to fix gutter rash/minor curb damage on your rims.

Note: This will generally only work on silver/polished rims with small lip on edge of the main lip (if ya get what I mean!). But may be able to be used on other wheel for various functions such as sanding before paint/powder coating etc.

A while ago I bought some second hand Brabus rims for my ride. They were in good general condition, with the usual minor nicks here and ther. One of the front wheels had gutter rash all around the outer lip. It wasn't too deep, but it was damn ugly. Now, I am a cheap bastard being half asian, but I also love giving things a crack. I had heard the local rim repairer couldn't do 19" rims, but never bothered to investigate, so I decided I'd give fixing these a go myself.

First I went out and bought two cheapish files, a straright cut bastard, and a plain flat bastard. I was having new tyres put on, so had the current Hankooks removed as I was gonna sell them off anyway. While the tyre was off I got down to work and did this.

First photo is of original curbage when I bought them. And I have used the same method twice, second time was for my bros small curb incident. (He did send me a nice set of Bahco files though!)

Original curbage around lips lip! All the way around

Curbrash.jpg

Tyre is removed from wheel, car is jack up (axle stands used of course!) at the back and rim put on. Essentially this is the poor mans lathe. So to clairfy. The cars rear end is up, and on axle stands. I can't remember if I removed the othe side wheel, but I think I did. I tryed the car in 1st gear with the engine at warm idle. It was a bit too slow.

Image0111.jpg

I found second gear with the car at idle to be a great speed for the wheel to spin at. And basically I sit there with the files (straight cut bastard and a standard flat bastard) and work the curb rash away. Here you can see metal I have worked from the rim. After the rash was removed, I did a rough sand, then a finer sand. I can't remember the grits, but I'd imagine 180-200 and 300-400.

Image0109.jpg

First time I did it, I was having new tyres put on anyway, and second time round I had the tyres rotated (staggered set, directional tyres,can't rotate whole wheel). So all up it cost me only time and about $30 for the two files.

After the file I sanded it to a smoother finish, then applied a little metal polish. No need to paint as it looks fine how it is!

Pretty easy and cheap for an arvos work. As you can see, this won't work on all rims, but may be adapted to do some of the work yourself if you are having your wheels painted/powder coated etc.

Please also note that safety must be considered paramount at all times. Axle stands must be used at all times and a second person should be there in case of emergency. Keep hands away form the wheel spokes. You get a hand caught in there and your in a whole world of hurt. I take no responsibility if you are injured trying this process out.

Good luck, I hope this helps some of you!

Richie

Link to comment
https://www.sau.com.au/forums/topic/275277-cheap-curb-rash-fix/
Share on other sites

yeah what they said .. if you're broke and can't afford a proper fix worth a try I guess. But seeing as how most pros charge $60-100 per wheel depending on damage, it's hardly worth the effort imho.

I got quoted $200 by Magman in Sydney to fix 2 wheels .. both have pretty bad gutter rash all around the outer lip and one of the wheels has a rather large chunk of metal (about 3-4cm) sticking out and needs to be welded back on

  • 2 weeks later...

so your sitting there with a file rubbing against the wheel while your car is jacked up and running on second gear. your broke but are you retarted as well? i would never trust jack/axle stands with the car running in gear at the same time. fromt he viberations of the cars running gear if the car falls you will get hurt pretty bad and your car will get damaged also.

i eman the results you got are great

but your method is very risky and id rather drive my car aroud with gutter rash and save up rather then doing it this way

  • 6 months later...

I dont know what some of you are complaining about. if you set it up properly it is perfectly safe.

i just did this, works great. after i finished with the file, i used some 120 sand paper and then finished off with 400.

i saved myself $150 a wheel and i actually enjoyed doing it.

i would be more worried about people hurting themselves with the tyre levers trying to get the tyre off the rim than actually hurting themselves filing the rim (i've changed a few sets of tyres on rims manually before and have had 1 or 2 close calls with tyre levers going flying up into the air). if you were worried about running the car to smooth out the rim, you could always just take the rim off and sit it on the ground and file it. wouldn't come out as nice though.

  • 3 weeks later...

you could always just hold the file on the outter side of the wheel so if you do slip your hand simple goes into the wheel arch, and if it does happen to hit the wheel it will only be the outside of the rim.

but to the people who are actually scared of this, there are a hell of a lot of more dangerous tools out there. basically all he is doing is using the car as a lathe. nothing scary there. i'd be more scared of a simply angle grinder than doing this (and i'm not scared of an angle grinder, although i am still cautious with them).

  • 3 months later...

Dont do this in an enclosed garage either... exhaust poisoning anyone???

But seriously, there are some people out there who should not be near tools, if they can handle them selves, and are farily good with this kind of thing... BIG dollar savings to be had.

I have done this in the past, just as long as you use common sense you should be ok. I also had a 2m kilswitch line rigged up too, so if you need to... hit the big red button. everything will stop rotating soon enough (especially in gear)

2nd person nearby is a VERY good idea aswell.

Not too shabby of a method. Provided you have a nice flat surface. People worrying about losing their hands. I doubt very much you need to apply such pressure onto the bastard to start shaving the wheel. Light pressure and keep your hands away from the gears. I would have tried this except my rims aren't silver, they're painted and I cbf matching the paint.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
×
×
  • Create New...