Jump to content
SAU Community

Recommended Posts

I plan on buying a new ecu in the coming weeks and I need a little help deciding which way to go. The car is an R32 with RB20DET and i've just installed a larger turbo, new manifold, external gate, cams and ajustable gears, ebc and a few other things.

I'd been planning for a while to go with the Nistune, until i went and spoke to the only local guy that does dyno tuning. (I'm out in the sticks). He's never had any experience with the Nistune, but he's a Vipec dealer and has done a few of them in skylines now.

So what I'd like to know, is whether either of the ecu's have any specific advantages? I do like the advantage of my car being tuned locally by a guy with a bit of experience on similar setups, but I also like the price of the Nistune.

Link to comment
https://www.sau.com.au/forums/topic/278238-nistune-vs-vipec/
Share on other sites

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

Yes the Vipec is a very decent ecu. You should go with it. However your tuner should also be able to tune a Nistune.

The vipec cannot be compared to the Nistune because they are totally difference ecu's. You can compare a power fc and a nistune like you can compare a Vipec & Motec.

They are totally different. one does the job and works okay, the other does the job and can make you breakfast.

If you go down the vipec route, you can pull out your ebc and use the vipec to control boost for just a added $130 part so you can get the vipec for a bit cheaper and have decent boost control as well.

for the price you can't beat nistune. it gives you all the features you need as far as being able to change injector size, afm and do full adjustment of ignition and fuel maps. and most of all, full installed and tuned it will probably cost a lot less than just buying the vipec ecu, which would then leave money in your pocket for other mods

There's one tuner in town and he does vipec. He's done a few skylines and some silvias and supras with vipecs now. His main clientel is v8's but he seems to be a decent tuner.

Other than that its a 5 hour drive to Sydney or 4 hours to Canberra.

Nope. I don't really mind towing the car to be tuned if i have to, but thats basically gonna add a few hundred bucks to the cost, and i still wouldn't have local support if something were to go wrong.

Vipec is starting to look like an attractive option! :laugh:

by the sounds of it vipec is the most viable option.. after you take in costs of towing etc if something goes wrong and so on.. might be a better to have a higher initial outlay of $$$ to save furhter $$ in the future "incase" something goes wrong

have you asked your tuner about power fc ?whats your plans with the car & whats the mod list, if its just basic upgrades, there is no need to go vipec.

Listed most of the mods in the first post. Its nothing crazy, but its further than the basic upgrades most people do. The turbo is a HKS T300s but i will most likely change that fairly soon anyway to something a bit newer and slightly more responsive. :pirate:

by the sounds of it vipec is the most viable option.. after you take in costs of towing etc if something goes wrong and so on.. might be a better to have a higher initial outlay of $$$ to save furhter $$ in the future "incase" something goes wrong

Thats pretty much the same train of thought i'm having.

in your situation with the distance i would go with what the tuner advises.

but i am looking at getting a Nistune soon, basically because my car is just a streeter, my tuner does both. and obviously i am gonna go the cheaper option because all i need is to maybe have the timing and fuel maps changed, and possibly allow for larger injectors and the Nistune will do that.

but i have heard great things about the Vipec, but i think $14k is enough to spend on a car in 8 months!

time to start holding onto my money

brez

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...