Jump to content
SAU Community

Recommended Posts

Originally posted by URMINE

exstatic.. i want the front bar and the grill have u got icq or msn(or pm me and ill send u my moby number) so we can have a chat over how to split up the costs?? if the $$$ is right ill buy it with ya...

ICQ 12886924 :P

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

light. if you want genuine they cost like 220 a pop or sumthing stupid. i just got some black perspex cut out the holes inserted (silastic)$1 light globe and hooked it up cost 10 bucks plus 1 hour wasted

lou15x- ill pm ya

pete

Is the kit made for a GTR or GTS as the GTS needs to be smaller (slightly) otherwise it looks ****.

I Have a 400r bar on my car i asked for a GTS bar but i got a GTR bar and its to wide by about an inch or so a side.

so when it is "made" to fit the front of the bar sticks out about a centimetre to far and the bottom of the bar sticks out to the side to much.

I am after a bar so far i have found UAS sell them GTS version that is.

Any one know if they are sold anywhere else maybe in QLD.

I got my bar of blits at the gold coast.

and check yah PM fatz

  • 1 year later...

this is very old

and not exstatic still owes me about 220 bux from this deal

anyone knows him please punch his light out to the tune of 220 dollars please

lol

come one ex static its only been 2 years m8 surely you can afford 220 now ya clown

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...