Jump to content
SAU Community

Recommended Posts

So i want to get an LSD diff for the rear. anyone know what the ratio is for them? im hoping (like the V35 guys http://www.skylinesaustralia.com/forums/Au...f-t279164.html) that there might be something else interchangable. if i start increasing power, i want to be able to put it to the ground properly..........

Link to comment
https://www.sau.com.au/forums/topic/280027-m35-diff-ratio/
Share on other sites

Actually, I meant Nissan website...

M35 Stagea mk1 full website

8th link down on the left.. Make sure that you have Babel fish all warmed up and ready to go...

But I do have UK R34 GT-R brochure....

thanks nick!!

whered you get the brochure?

i should scan and post up the nismo option and nissan aero option ones i got from IM..........

Edited by nickcorr
Link to comment
https://www.sau.com.au/forums/topic/280027-m35-diff-ratio/#findComment-4725757
Share on other sites

Isn't the diff just an r200 Shortnose?

All you should need is a LSD centre, swap your ring gear over and set backlash.

Lots of options for a donor centre, r32, r33, r34, s13, s14, s15...

I'm pretty sure the only IRS in recent times that's any different is Z33 300ZX; which is r230 diff.

Please feel free to correct me if I'm wrong, it's happened before...

Link to comment
https://www.sau.com.au/forums/topic/280027-m35-diff-ratio/#findComment-4727545
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...