Jump to content
SAU Community

Recommended Posts

Hey guys and girls,

Im buying another car as ive sold my GTR.

Ive found one i like and ive put down a deposit.

He has said he had to take a car loan out to buy the car and is still paying it off.

As me the buyer what do i have to do differently ? if anything?

As ive never bought a car that is under finance.

Link to comment
https://www.sau.com.au/forums/topic/280046-buying-a-car-with-a-loan-on-it/
Share on other sites

Wouldn't you need to find out how much he has left owing on the loan and then ensure that the money you are paying him for the car is going to that loan, rather than in his pocket?

So, payout the loan (thus car is fully owned by the seller), than whatever is left behind goes into he's pocket.

Think that would be the procedure

Wouldn't you need to find out how much he has left owing on the loan and then ensure that the money you are paying him for the car is going to that loan, rather than in his pocket?

So, payout the loan (thus car is fully owned by the seller), than whatever is left behind goes into he's pocket.

Think that would be the procedure

In this case lets just say the dude is selling his car to you for $15K....he has $10K owing to the bank....then what you would be doing is paying $10K to the finance company (in this case BANK) and giving the DUDE (the seller) his $5K.....i would be personally going to the bank and asking them for advice and they will be able to point you in the right direction and at the same time organise everything for you.....

if you paid the DUDE $15K and he does a runner.....guess what....your the owner of the new vehicle....and you most likely will be required to pay the payout amount.....

Same with insurance when your car is financed....the insurance company will payout (in case of a writeoff) the financial company what you owed them and then give you whatever is left

TREAD WITH CAUTION ON THIS ONE MY FRIEND

Yep all the advice above is spot on...

Get payout figure on his loan, make out cheque to his finance company, then cash for any difference or seperate cheque. Do the signing of changeover forms at the bank when he deposits the cheque(s) and MAKE SURE YOU GET A PRINTOUT SHOWING ZERO BALANCE ON THE LOAN!!!

Good luck.

well i have a contradicting story. When i purchased my s14 the guy had finance on it. I paid him, he continued paying his loan. When i went to sell it a guy backed out cause he found out it still had a finance against it so i called the company the finance was with and questioned them. 2 different times i rang to be sure i was getting the right answer and they informed me that if he did a runner they would be chasing him for the money as the finance is in his name. They wouldnt be involving me at all, be it for the car or money. Havnt heard from them to this day and i see the car kicking around every now and then.

As Luke said, the only time they will come chasing you is if the loan was secured against the car. In which case the bank will order repossesion papers for the car if the person named on the finance defaults. But i could be wrong, had a similar situation a few years ago too.

James is correct.

If the owner took out a personal loan to purchase the car but wasn't secured against the car then you'd be safe buying it cause if he did the runner the finance institution would chase him.

However, if the loan was secured against the car, either pay the finance company direct (and make sure you keep the receipt and have the rego papers) or avoid it with a 10ft pole.

Thanks for the advice. As it turns out its only a PERSONAL loan not a loan on the car so its fine. But as said above IF it was a car loan. Best way to do it (or as i was told by his bank) would be to go in with him to the bank with the cheque and pay it out there and then with him. theyll give you the loan payout statement there and then

Even if its a personal loan it can still be secured agasinst the vehicle. But yeah, do as you said and be there when its paid out and get a print out of the balance sheet for the loan. Probably wouldn't hurt to ask if it can be closed while your there too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...