Jump to content
SAU Community

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

yeah, looks like the 28th never happened lol

this also includes PM's. eg. i received a PM today, as new, that I had already recieved on the 27th. And no PM's from the 28th exist.

no complaints here. just keeping you guys informed.

Yep, and the evening of the 27th as well I think!

I received 3 PM's (email notifications), but there are none here.

Just wondering if PM's and posts will be re-instated.

I know you guys would have been onto it for a while now, so no complaints... just curious if the posts/PM's are still on a disc somewhere or are they lost?

Hiya,

Forums have been down for me for most of the day - I was unable to resolve the skylinesaustralia.com domain; Neither of the nameservers appeared to be reachable. A traceroute wasn't suceeding either. Bypassing DNS, I tried telnetting to port 80 on 208.69.126.31 (though this appears to be one of the DNS servers!), and this failed too suggesting it was more than a DNS failure.

I'm guessing either some sort of server failure or a routing issue from Australia? I tried from 3 different IP ranges (home, two from work) and still no luck. Are you guys aware of any issues? Do you guys report on those issues on the forums somewhere so I can not bother you in future? ;)

jenna

yeah, looks like the 28th never happened lol

this also includes PM's. eg. i received a PM today, as new, that I had already recieved on the 27th. And no PM's from the 28th exist.

no complaints here. just keeping you guys informed.

Edited by Munkyb0y
Just wondering if PM's and posts will be re-instated.

Anything that is missing - wont be returning.

As per the announcement some features will slowly come back online as things return to normal... however the core stuff PMs/Posts/Threads if they are not there now; have gone bye bye's.

The backup by my rough checking shows the last posts were from approx 4am-5am on the 28th being thats the last post i could see upon the restore.

In effect most of the 28th went missing. So a bit more than a few hours, but less than a day's worth overall.

Shit happens unfortunately guys, no need to get too worked up over it :P

Im lucky all the SAU-SA members setup/creation work i did was still there hehe, that would have been a solid 4hrs of config changes out the window!

Yeah sorry guys, a bit more was lost than initially suspected. :P

Also, the search indexes are being rebuilt, it will likely be back online tonight or tomorrow morning.

Thanks for your patience. :(

heh, I don't know how much work and effort goes in, but I imagine it is a fair amount.

Good work getting things more or less up to speed in a relatively short amount of time guys.

Can I ask that the clock is fixed up though?

It is about 4hours behind.

Thanks for your dedication & hard work on this, PranK.

As a sysadmin/netadmin myself for work, and having hosted car forums on my personal servers in the past - I know how effort goes into managing/maintaining all this stuff. Keep it up ;)

2gig, 4gig, etc fiber raid???

and what servers are these?

and what are you backing up to? external server or a san or tapes?

Um, why all the questions?

For the record, backups are now taken 4 hourly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...