Jump to content
SAU Community

Flutterdump?

Ninja gts25t
 Share

Recommended Posts

Benzino33 Experienced

Benzino33

Posted
Posted
What is flutter dump? the otherday a r33 blew past me and did this i wana know how to do this

thanks :)

Are you referring to the blow off valve noise or "turbo dose" noise?

If so here's a thread all about it.

http://www.skylinesaustralia.com/forums/st...Tu-t276031.html

Link to comment
https://www.sau.com.au/forums/topic/282335-flutterdump/#findComment-4754663
Share on other sites
lineskee 33 Community Regular

lineskee 33

Posted
Posted

i didnt think it was even possible to get wastegate flutter. I think you may be meaning an external wastegate? if the car was really loud going past while on boost, it would be that. its a screamer pipe that goes onto the wastegate. this is illegal to have, but on the right setup it sounds good.

Link to comment
https://www.sau.com.au/forums/topic/282335-flutterdump/#findComment-4754718
Share on other sites
bradsm87 Proficient

bradsm87

Posted
Posted

Flutterdump is when the BOV is a cheap POS or the spring in the BOV is too stiff and U back off and it starts fluttering then the BOV vents. It's considered a problem and can be fixed with a much softer spring. As long as the BOV is plumbed back like it should be, it can be soft enough to stay open on idle without and probs. As soon as U give it the tinyest bit of throttle, it slams shut.

Link to comment
https://www.sau.com.au/forums/topic/282335-flutterdump/#findComment-4754998
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      Looking for a part number for this part here

      By Duncan · Posted

      So....to find any R chassis part number, get your VIN (will be something like ER33-xxxxxx for you) and go to: https://www.amayama.com/en/genuine-catalogs/nissan and enter it. From there you have access to a web version of Nissan's part system, FAST. It is a bit tricky to get used to, so maybe have a shot and post up what you think.  You can also search by general model but note in some cases your car might have different options so VIN is safest.  On diagram 211 I got 14075-75T16 for Connector, Water Hose If I search for part 14053‑21U10 that you posted, that is also a water hose but not the one bolted to the plenum and 14075‑04U00 is the fitting where the water hose goes into the block.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Yeah now we are talking I much prefer coolers in the front middle because it lessens the chance of a small bump to a corner stopping the whole event. I was thinking the AT cooler can move out of the radiator, delete the AT/engine coolant interwarmer and mount a separate cooler with a thermoswitch somewhere further back as is common in racing, that would be one thing. Beyond that, the engine oil cooler is an obvious one to move to the wheel arch, potentially one on each side, but unused space is an issue. I did have a earlier pic with the bumper off but it doesn't show how busy the corners are: DS is full of the auto driving sensors and PS is totally fully of windscreen washer fluid reservoir But ultimately I was hoping to keep the AC, and the water/air heat exchanger is fundamental so it is not just the radiator that needs to be in front BTW here's airflow to the rad as it ran at the track (one horn is gone now and I'll remove the lights next time):
    • turboedsloth
      New Wasteland Wa Topic

      By turboedsloth · Posted

    • V35_Paul
      Infiniti Q60 Navigation Update

      By V35_Paul · Posted

      your right the maps for Australia came out in 2017 but are 2010 maps. i got the updated maps SD card put it in and it was the same. Same maps in my Brothers Nissan Patrol. 2020 i think his car is
    • silviaz
      Returning after a long time!

      By silviaz · Posted

      Yeahhhh, the costs have killed me. Spent more than the cost of an engine rebuild and it most mostly servicing and a tune lol.
×
×
  • Create New...