Jump to content
SAU Community

Recommended Posts

  • Replies 114
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 months later...

Well im back at it again,After power cruise this year and the car being down on power and not performing like it should.......it soon come to pass that my rb26 had packed it in and thrown a ring lan in No 6.

SOOOOOOO like normal i can t just take the easy road i have gone out and bought some new goodies for my gtr.

Nur spec 34 gtr rb26 with head work done by prime in japan!

Jun oil pump

N1 water pump

6 pot greddy front brakes

6 boost manifold twin scroll

264 hks cams 10.01/10.08 lift

Greddy twin pipe

turbosmart 45mm gate

And im currently looking at one of the new billet range of turbonetics turbos...............

Pictures to come as always i have some but not all.

I know its been while but after you cactus your motor you do not even want to open the door to the shed.......

Watch this space!!

Edited by Gtir-keiron

they always used to "fail" under race situations. not sure if these are a new breed or not but the tuner i use is a TS agent and he wont use there waste gates as he has seen to many fail.

Tial stuff is cheap as out of the states at the moment as well. and ive never read a bad thing about them.

im sure it will be fine im just not a fan.

  • 2 months later...

So to be on the safe side i had my 34 nur motor pulled down and crank checked due to the fact the car it came out of had been side swiped.

Turns out the crank was bent

So i have ordered a new crank

cp pistons manly rods

arp headbolts

acl bearing kit

new gasket kit

turbonetics gtk billet 750 split pulse rear.

Hope to have this all in and tuned running for power cruise this year

hoping for 550 to 650 hp at all 4 wheels on pump but we will see how that goes.

  • 4 months later...

Had a change of direction,

Head changes are VCT and billet custom cams

Precision 6766 cea billet wheel .84 twin scroll turbo

6 boost twin scroll manifold

Magnaflow fuel pump and fuel system

Motor is currently being assembled.

ERD in brisbane does a VCT setup for a 26 head with a custom billet cam to your liking and a vct cam gear,That i am having converted to adjustable :D

they say you can get 20 degrees out of it im unsure as of yet but im tuner and mechanic are very enthusiastic about the set up.Soon as its on the dyno ill post up some dyno sheets to see how it effects the larger turbo :D

I talked to a good mate noel who is good friends with the people at erd he said hes seen a old school to4z bush bearing turbo with vct and it bought it on 800-1000 rpm quicker spool time.

Will be intresting to see how it goes mate.

You can google ERD they are also a supporter of this website mate.

  • 4 years later...

I  know i have not been on for quiet some time due to real life a shithouse mechanic f**king me over and having to do a full rebuild after seizing my own property back from said unamed mechanic but things are comming to a head.

Where i am at

Motor is NUR engine i bought off another member on here a few years ago and since them i have had the entire motor pulled down and rebuilt,

Billet 276 degree custom cam shafts to suit a variable cam timing off a rb25

over size valves supertech double row springs very ported head.

86.5mm forged pistons rods all the goodness.

Currently awaiting a new 6boost manifold and 50mm progate split pulse

i have 2 turbos but i have chosen to go the smaller of the 2 a 6266 gen 2 precision over the 6766 dual bb precision.

 

I have a 26/30 6boost manifold and gate to suit the 6766 turbo ill be offloading once im finished all new never used.

 

Just a quick update i hope the car will be tunned and on the road early in the new year. pictures to come.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...