Jump to content
SAU Community

Recommended Posts

on the other hand anyone tried Kumho KU31?

I had them on a previous car, they were a pretty good balance of price, grip, road noise and wear. Actually I did have them very briefly on my current car on the 18's, only drove about 50km and since the car hadn't been registered/insured for about half of that I was taking it pretty easy :D I seem to remember they were the second cheapest tyre in stock size that had the right sizes available front and back but at that size and profile it's more the performance end of the market...

My favourite tyres (previous car again) were Goodyear Eagle F1 GS-D3's, heaps of grip, really quiet, excellent in the wet but cost a bit more.

I tend to find if you care about performance with tyres, you are better off spending a bit more and getting something good, because if you get crap tyres you've got to put up with them for a long time.

Tire rack I think is ok for a bit of research:

Tirerack 2003 Infinity G35

For example Kumho KU31's aka Ecsta SPT's get a rating of 6.9 but are among much more expensive tyres with similar ratings.

they are a cheap and nasty tyre that belong on korean cars. if you cant afford the tyre then you cant afford the rims. doesnt make a lot of sense to me to spend a lot of $$ on a sports car to put shit tyres on it and undo all of the manufacturers work.

if u want cheap + reasonably good tyres...get the Federal's 595 or Archilles ATR they are cheaper than the nankangs with better grip and less road noise. Dont know about wear rate though coz i've never kept a set of wheels long enough to wear the tyres out.

  • 4 weeks later...
  • 3 years later...

Cant help you with the Michelin, however I recently (3 weeks ago) replaced my two front tyres from BF Goodrich (came from Japan on the car and the same models are not available in Aus) to Yokahama Advan Sports (245x19 35).

Since changing, it appears the front have WAY more grip. The Traction control kicks in much later; it is now more me that holds back on corners than reaching the point that the traction control kicks in.

I have noticed if I do try to push it to find the grip break point, the rears (Falken FK452 285x19 35) will break first. Not a fan of over-steer but at least I know the fronts are grippy. I am expecting pretty low KM's from these, but I could be wrong.

Only had experience with a little rain thus far, but so far, pretty happy. They are not cheap. I think retail is over 400 each.

nankangs suck what on earth are you guys thinking running shit tyres on a sports car?tyres have a bigger effect on handling than ANY other component.

get the best tyres you can afford,at a minimum something like Bridgestone Adrenalin, Dunlop Sport maxx or Yoko S.Drive or similar..

I had Yokohama Advan Sport which were good,now running Bridgestone RE11s which are really good!

i would consider a better tyre in a narrower size over a crap tyre in a wider size too.

Nankang is probably better than chinese ebay tyres...

if youre like me, and you only need tyres to stop your rims touching the ground and to last forever, then anything chinese is fine. but if you want grip in corners... spend the extra $$ but expect a short tyre life.

ive seen Simex used on the track in the wet and do well.....

i can't fault my Achiles ATR Sports. Had them on the car since September, tread still looks the day that i put them on minus the nipples. I do alot of spirited driving, i don't break traction very often either so that's probably why. But the car is my daily, i am happy with these tyres but my next set would probably be some Federal 595's. Achiles ATR's are a noisy tyre, but i always have windows up music on and aircon so i never notice it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...