Jump to content
SAU Community

Recommended Posts

Hey, first post :devil:

Was driving from Altona Meadows -> Williamstown today on the M1. Just after where it splits, left to (Old?) Geelong Road, right to continue on the M1 there is roadworks, the speed limit is 80KM/h down from 100KM/h. I know there's a fixed speed camera, or 'traffic monitor camera' there (just after it splits). Do they adjust the detection speed down from 100 -> 80KM/h when there's roadworks?

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/284687-fixed-speed-cameras-roadworks-on-m1/
Share on other sites

yeah i dont think they do.

half the time they dont work right anyway, i doubt they are going to recalibrate them each time.

keeping that in mind, any one of those workers could trip and fall in front of you, court's wouldn't be in your favor if you hit them at 100kmph

Well most people were sitting on 100KM/h anyway. If someone is sitting on 80KM/h, they're holding up all the traffic anyway. I'm all for 'smooth driving' where everyone's doing the same speed, much safer than everyone doing a different speed.

And I'm all for shooting up with a whole bunch of junkies, much safer than doing it in an alleyway alone!\

People in general are lemmings, if someone goes the right speed, others will follow (save for the raging BMW drivers).

And I'm all for shooting up with a whole bunch of junkies, much safer than doing it in an alleyway alone!\

People in general are lemmings, if someone goes the right speed, others will follow (save for the raging BMW drivers).

You are correct, after all it is perfectly logical that the speed limit is reduced to protect the workers who are working behind a concrete barrier, why not slow the freeway down, after all how many times have you seen a car break through those concrete barriers?

You are correct, after all it is perfectly logical that the speed limit is reduced to protect the workers who are working behind a concrete barrier, why not slow the freeway down, after all how many times have you seen a car break through those concrete barriers?

The concrete barriers aren't all the way along the freeway, they only cover some sections along the monash - there's works on the westgate side too that have none.

I suppose you could only lower the speed limit in sections where workers are exposed, but then people would complain about numerous speed changes, and not being able to see that far ahead. And say one of the barriers cops a hit at 100kph, wouldn't want to be the poor bloke standing on the other side of it when the wall jumps out at you - they aren't fixed to the road surface.

The concrete barriers aren't all the way along the freeway, they only cover some sections along the monash - there's works on the westgate side too that have none.

I suppose you could only lower the speed limit in sections where workers are exposed, but then people would complain about numerous speed changes, and not being able to see that far ahead. And say one of the barriers cops a hit at 100kph, wouldn't want to be the poor bloke standing on the other side of it when the wall jumps out at you - they aren't fixed to the road surface.

Lets also take into account the amount of time that the speed limit is reduced but there is no one there, cant see why the dont put up those variable speed signs, when the guys get there in the morning they change them and when the last guy leaves they change it back, not real hard to do.

Lets also take into account the amount of time that the speed limit is reduced but there is no one there, cant see why the dont put up those variable speed signs, when the guys get there in the morning they change them and when the last guy leaves they change it back, not real hard to do.

+1

Preach it Brotha!

  • 9 years later...

Hi OP. What ended up happening even though this was a long time ago? This is because I'm in a similar situation. 

I'm from Sydney and was recently driving from Melbourne Airport down to Geelong via the M1. Being as it is unfamiliar place for me, I was being even more careful with my driving. Sadly, I was not careful enough. 

I was in cruise control set to slightly under 100km/h, and did not realise the yellow painted lines on the road meant reduced speed to 80km/h due to the roadworks (silly me I know! but never seen such things in Sydney). There was a fixed speed camera in place, but not sure if they reduced the limit on the camera (as some cars were wizzing past me). 

I believe it was the camera near Princes Freeway, Forsyth Road Bridge, Geelong Bound, Point Cook. Any opinions would be appreciated! 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
    • Stop looking at the garage floor, and turn the radio up a bit louder if there's any strange noises...
    • No. Turbo shuffle and surge/flutter are not the same thing. Specifically, on a GTR, turbo shuffle has a definite meaning. On a GTR, the twin turbos are assumed to be the same thing and to operate the same way, exactly. In reality, they do not. Their exhaust sides are fed and exhaust a little differently, to each other. Their inlet sides are fed and exhausted a little differently, to each other. Consequently, when they are "working" they are often at slightly different points on the compressor map compared to each other. What this means, particularly when coming on boost, is that one of them will spool up and start producing extra flow compared to the other, which will put back pressure on that other compressor, which will push the operating point on that other compressor up (vertically). This will generally result in it bumping up against the surge line on the map, but even if it doesn't, it upsets the compressor and you get this surging shuffle back and forth between them That is "turbo shuffle" on a GTR. It is related to other flutter effects heard on other turbo systems, but it is a particular feature of the somewhat crappy outlet piping arrangement on RB26s. There are plenty of mods that have been attempted with varying levels of success. People have ground out and/or welded more material into the twin turbo pipe to try to prevent it. Extending the divider inside it works, removing material doesn't. There are aftermarket replacement twin turbo pipes available, and these exist pretty mush purely because of this shuffle problem.
    • You can temporarily* use lock collars to keep it in place until you can do the bushes, back the nuts off, slide them in, snug back up. *temporarily is often for ever
×
×
  • Create New...