Jump to content
SAU Community

Recommended Posts

Hey guys

I've finally gotten around to addressing this problem on my car. The rear windscreen washer isn't squirting any water out, while the front ones are working fine. I've had a look on the forums and I've come to the conclusion that the hose is probably blocked.

What I'd like to know is, has anyone else had this problem? and if so, how did you go about fixing it? I assume I'm going to have to remove the head liner if possible.

Thanks in advance :banana:

Link to comment
https://www.sau.com.au/forums/topic/286907-rear-windscreen-washer-is-blocked/
Share on other sites

well, you need to check if its a blockage or the pump is dead

so remove the pipe from the end of the line at the nozzle and hit the squirter, if it comes out, the nozzle is dirty. if it doesnt, there is either a blockage further up (check it by following the pipe) or the pump is dead. youll need to use your head with this one, but its quite simple!

  • 12 years later...

I suspect the check valve is blocked 'cos I've replaced the pump and that now works but still no rear squirt. Can you advise how to get to the check valve (see part 27461N on the attachment)?

R33 Rear Windscreen Washer Hose Assembly.pdf

Awwww.....Goldzilla posted here

Did you try what zei20l said? nozzle is the most likely thing to be blocked and easy to check by pulling the hose off the back of it.

Beyond that, looks like the hose runs along the inside of the sill where the wiring is. You'll need to pull up the kick panel (carefully, don't break irreplaceable clips!). Pull it apart at each connection you can to narrow down the blockage.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
×
×
  • Create New...