Jump to content
SAU Community

Recommended Posts

my friend did have one fail, bad solder joint from his ebay ones...

Yep it's possible, something like that we can't pick up in QC checks...vibration will be the thing that finally triggers a joint failure. Due to the design of the T10's now, even that's a thing of the past, shame we can't pass the change down to the T5's

Currently via ebay I'm running about 10% off base dash kits.

Yep it's possible, something like that we can't pick up in QC checks...vibration will be the thing that finally triggers a joint failure. Due to the design of the T10's now, even that's a thing of the past, shame we can't pass the change down to the T5's

Currently via ebay I'm running about 10% off base dash kits.

Hey dan do u still have the 3 interior lights for 30$ saw them on another topic just wandering if i can still get some???

Im puttin the dash ones in friday ill take sum piks :P

Thanx mate.

Yep it's possible, something like that we can't pick up in QC checks...vibration will be the thing that finally triggers a joint failure. Due to the design of the T10's now, even that's a thing of the past, shame we can't pass the change down to the T5's

Currently via ebay I'm running about 10% off base dash kits.

I had some problems with the earlier red leds I bought (voltage issue) but since I switched to the new blue ones (16v) I've had no problems at all... been running solid for 18 months now

-D

Yep it's possible, something like that we can't pick up in QC checks...vibration will be the thing that finally triggers a joint failure. Due to the design of the T10's now, even that's a thing of the past, shame we can't pass the change down to the T5's

Currently via ebay I'm running about 10% off base dash kits.

Yeah I do have to say this Dan666 sent out a new one without issues on the one that failed. fantastic service!!!

Hey dan do you have the link to your A/C ones for the R34 ? I have a lot of people asking me all the time from USA,, much easier to send them the link overseas ..lol

Yeah I do have to say this Dan666 sent out a new one without issues on the one that failed. fantastic service!!!

Hey dan do you have the link to your A/C ones for the R34 ? I have a lot of people asking me all the time from USA,, much easier to send them the link overseas ..lol

I don't actually have seperate listings for them on ebay, best way is to contact me directly to arrange a set. Still trying to get my webpage built...hopefully in the next 6 months and I can leave ebay for good:S

I don't actually have seperate listings for them on ebay, best way is to contact me directly to arrange a set. Still trying to get my webpage built...hopefully in the next 6 months and I can leave ebay for good:S

Would like to add, Dan sent the leds really quickly and for a very good price - you'll have no problems with his series 2 led's...

and incidentally, I can help people fit the leds but only in R32's as Im not familiar with the 33s or 34s

-D

Very happy :thumbsup: to say that Steve (Madaz :down: +2 r34 led installs for him) came over and we installed the led's big thanx to him for helpin out!!!!

Wasnt as hard as it looked just need a bit of confidence wen u go in to try to dismantle it all!!

If anyone needs help with doin it or has any questions let me or or steve if he's not busy.

Cheers for all the help guys n again thanx Steve ;)

Will take sum piks tonight wen im out n post em soon!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...