Jump to content
SAU Community

Recommended Posts

Hey All

Im thinking of getting a black and white theme going on my R33 and going the usual with bonnet and gonig to paint my stockies black.... but was wondering what your thoughts are n doing the petrol cap/cover in black aswell... I like the look and think its a bit different and adds a different look to it...

I have grab a pic of a car and just used paint to demonstrate... All feedback welcome good or bad

cap.jpg

Link to comment
https://www.sau.com.au/forums/topic/289889-petrol-cover/
Share on other sites

i think it would look wierd but couldnt you find a wrecked black one and take the cover off and put it on yours that way you can change back if you end up hating it.. would prob be cheaper then getting yours sprayed anyways

Link to comment
https://www.sau.com.au/forums/topic/289889-petrol-cover/#findComment-4851675
Share on other sites

i think it would look wierd but couldnt you find a wrecked black one and take the cover off and put it on yours that way you can change back if you end up hating it.. would prob be cheaper then getting yours sprayed anyways

Ah acually quite a good idea... might have to look into this

Link to comment
https://www.sau.com.au/forums/topic/289889-petrol-cover/#findComment-4851764
Share on other sites

I kept looking at that picture trying to think of what looks weird, then it hit me, you did the fuel cap on the wrong side :(

lol yeo.. i couldnt find a decent side pic of a white 33 on google so i just used this one and drew it on in paint hahaha but still gives the general idea of what it would look like

Link to comment
https://www.sau.com.au/forums/topic/289889-petrol-cover/#findComment-4854062
Share on other sites

i don't like it, but that's just me

another way to do it without painting it (or having to find a black one to try) would just be to wrap it in cling wrap then put some black contact paper or sticker vinyl on it. that's actually what i did with the front grill on my r33.

dsc01438nb2.jpg

i used both white and black decal vinyl to make it look a little bit more like a series 2 grill as i didn't want to paint it and then not like it.

Link to comment
https://www.sau.com.au/forums/topic/289889-petrol-cover/#findComment-4856711
Share on other sites

+1

Leave it white mate. I think that would look the best. It would look very out of place being black.

On another note go with the black/look. Just do it with carbon fibre. Bonnet, Spoiler Wing Blade, Window Pillar Panels, Mirrors.

Link to comment
https://www.sau.com.au/forums/topic/289889-petrol-cover/#findComment-4857518
Share on other sites

If your trying to get the "Panda" Spec look, your going to have to make a few other things black, so your cars has some consistency with it.

If you must then Cling wrap it like what mad082 said or just leave it.

Link to comment
https://www.sau.com.au/forums/topic/289889-petrol-cover/#findComment-4862199
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
×
×
  • Create New...