Jump to content
SAU Community

Recommended Posts

Hi guys,

I put an 040 in the car a few months ago. Ran fresh wiring, new relay etc etc

Up until today, you could just hear it humming/sucking away. From inside the car you could just hear over the exhaust & from the outside you could barely hear the pump at all.

Today it has started whining/buzzing and it is significantly louder than normal. Should I be worried?

Edited by Yeedogga
Link to comment
https://www.sau.com.au/forums/topic/289920-bosch-040-just-got-more-noisy/
Share on other sites

if it makes you feel better, my 040 makes a hell of a lot of noise, all the time. gurgles, buzzes, whining...

very noisy pump. car has always been fine though, been running it for a year or two now.

I don't have a gauge so I haven't been able to tell. Car seems to be running fine though.

Mate go get an autometer gauge that you can put in your engine bay they're like $20 and hook it up to your regulator, its such a cheap mod for important information if you're running more than base fuel pressure.

Check your tank for shit!

Pull the pump out and inspect it for black dusty crap on the bottom. If that or anything else is on the strainer of the pump you need to remove the tank and have it cleaned.

My 044 went this way too, exact same symtoms. Started also getting fluctuating pressure.

Ripped it out and went a 023, still never figured out why it died. Was a genuine 044 too, strainer was clean, good wiring etc.

There just getting so hit/miss now it's not funny.

I really don't think it's anything to worry about, my 044 has been like this for a couple of years now with no issues what-so-ever.

My guess as to WHY is that it's probably working harder to pump the thinner hotter fuel around. It's basically because there is excess fuel travelling to a hot engine bay and back. Standard, our cars run a control module that drops voltage to the fuel pump at idle, these tend to get removed when aftermarket fuel pumps go in.

Edited by bubba
if it makes you feel better, my 040 makes a hell of a lot of noise, all the time. gurgles, buzzes, whining...

very noisy pump. car has always been fine though, been running it for a year or two now.

Same with mine. Mine has a very loud buzz & grgule sound since day 1 of getting it installed when my stock one died. The exhaust noise covers the pump noise up inside the car, however outside its very noticeable when you are near the rear of the car.

Being fine for about close to a year now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
×
×
  • Create New...