Jump to content
SAU Community

Recommended Posts

I recently took my car into a mechanic to get a very slight coolant leak at the back of the engine checked out only to find out that i have a blown head gasket and the said mechanic didnt want to touch it as he was unfamiliar with the engine. As i have my car up for sale i don't want to sell it as is or do a dodgy on it so who would you recommend around the southern area to fix this. I was thinking Boostworx because i would like it done properly. any other ideas? IS this a common and expensive job? What should i be looking at paying roughly?

Basically the leak is coming from the very back of the engine and dripping down onto the gearbox. I can smell coolant after i have been driving but its such a slow leak that it never reaches the ground. I only notice a slight drop in the coolant level after a week of driving. The engine itself runs perfectly.

Any help would be appreciated.

Dan

Edited by Muges180
Link to comment
https://www.sau.com.au/forums/topic/291454-blown-head-gasket-repair/
Share on other sites

Basically the leak is coming from the very back of the engine and dripping down onto the gearbox. I can smell coolant after i have been driving but its such a slow leak that it never reaches the ground. I only notice a slight drop in the coolant level after a week of driving. The engine itself runs perfectly.

Any help would be appreciated.

Dan

Are you 100% sure its a gasket? Sounds like one of the hoses leading to your heater core has split. I had this same problem earlier in the year. Will cost a bit in labour depending on your engine and how easy it is to get to said hose... If your gasket had deteriorated you'd probably be finding a bad color in your exhaust due to coolant in the cylinder head...

Boostworx or John @ Southern Hitech can help you if you're down south, Gil @ Road & Track can do it if you're up north

-D

You'd know if it was the head gasket... milky shit under the oil cap, bubbles in the radiator when you take off the cap, etc.

Sounds like a hose to me. And head gasket repairs aren't cheap...

Exactly.I found the same thing the other day, just a hose. the oil is fine and the radiator isnt bubbly.

Ive located the fault hose after a bit of searching, jus gotta replace it tomorro

picture the very back of the rb25 between the firewall and the block. thats where its leaking from but i cant see exactly where its coming from because there is no room.

yiap definately sounds like heater core/hose leading to heater core

-D

I would hazard a guess and say its your coolant line from behind the inlet manifold, which runs around the back of the head, to the turbo. If the engine has ever been removed, chances are the pipe might have been crushed by the firewall (and subsequently a leak forming), or its simply the hose section right near the inlet manifold. Either way, its a bitch to get to (read: impossible). Removing the engine might be required.

You'd know if it was the head gasket... milky shit under the oil cap, bubbles in the radiator when you take off the cap, etc.

Sounds like a hose to me. And head gasket repairs aren't cheap...

Not necessarily.

the coolant isnt discoloured at all. The mechanic did a preassure test on it and said it was the gasket but im still not overly convinced. might take it into Shaun for a second opinion.

The facts so far:

Coolant leak at back of head.

Coolant level goes down in a week.

Pressure test confirms coolant loss in system.

You can have coolant leaking from a head gasket without it affecting your oil if the passage of leak is directly from an external water jacket....they don't always track to an oil gallery so oily radiators or milkshakes in cam covers aren't always present with blown head gaskets.

The other thing to check is whether exhaust gasses are entering the coolant system but then again, leaks don't always track between combustion chambers & water jackets either.

I would hazard a guess and say its your coolant line from behind the inlet manifold, which runs around the back of the head, to the turbo. If the engine has ever been removed, chances are the pipe might have been crushed by the firewall (and subsequently a leak forming), or its simply the hose section right near the inlet manifold. Either way, its a bitch to get to (read: impossible). Removing the engine might be required.

im no expert, but had this happen to me twice. no real warning (temp didnt go thru the roof, no milky residues) but a distinct smell of coolant and a lack of coolant after a few days / week

i think flick had the same trouble with her 32 when she had it too. doesnt bring the temps up to higher than normal temps until theres no coolant / water left in the system

thatd be the first (and less expensive) option to get checked. if those hoses are fine then it'll be the gasket

/2c

I would hazard a guess and say its your coolant line from behind the inlet manifold, which runs around the back of the head, to the turbo. If the engine has ever been removed, chances are the pipe might have been crushed by the firewall (and subsequently a leak forming), or its simply the hose section right near the inlet manifold. Either way, its a bitch to get to (read: impossible). Removing the engine might be required.

ive changed that hose twice now once on my sons car and once on my own first time took me a couple of hrs and the second time less than a hr .

the second time i used a pair of pointy nose pliars about 12 inches long and that made the job a shit load easier . still not a pleasant task at the best of times but buggered if i would pull a motor just too do it tho

You can have coolant leaking from a head gasket without it affecting your oil if the passage of leak is directly from an external water jacket....they don't always track to an oil gallery so oily radiators or milkshakes in cam covers aren't always present with blown head gaskets.

The other thing to check is whether exhaust gasses are entering the coolant system but then again, leaks don't always track between combustion chambers & water jackets either.

Just what I was thinking.

Can you get a small inspection mirror down there, like what a dentist would use?

Not necessarily.

The facts so far:

Coolant leak at back of head.

Coolant level goes down in a week.

Pressure test confirms coolant loss in system.

You can have coolant leaking from a head gasket without it affecting your oil if the passage of leak is directly from an external water jacket....they don't always track to an oil gallery so oily radiators or milkshakes in cam covers aren't always present with blown head gaskets.

The other thing to check is whether exhaust gasses are entering the coolant system but then again, leaks don't always track between combustion chambers & water jackets either.

beat me to it. i have a bore scope if you need to use?

55791.JPG

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • jeebus. glad you weren't under it while performing the stunt. Also thanks for the link to the wheel measurer, exactly what I needed
    • In the older stuff there were very significant differences 2wd to 4wd, for example Stagea had strut front end for 2wd and double wishbone for 4wd so it was not minor to swap. From poking around the 2wd v37, it *looks* like it might be more possible; some of the parts specifically have "2wd" stamped on them which suggests the platforms are more similar. You'd still want to start with a 4wd half cut to swap stuff from though. I'd suggest if you don't have a tune on the ECU you don't really need one on the trans either. Throttle mapping is in the ECU side (and you can always use a Roar Pedal if you want the throttle to actually respond to your foot), and really if you are happy with the stock power you probably accept the stock trans behaviour too....its all made to be "sporty" not racey.
    • So, updates. I have not washed the car since it came back from Tassie. I've driven it around a bit but not got around to actually sorting it out. I DID raise it because I cracked the rear bar leaving a hotel which was very distressing. Interestingly, the car drives more compliant now that it's raised a fair bit (5mm front, 15mm rear). Also noticed that my FR height was 10mm lower than FL. So that's now sorted out, too. I also bought this and had it printed: https://www.etsy.com/au/listing/1576422240/wheel-and-tire-fitment-tool-universal?ref=shop_home_feat_1&dd=1&logging_key=08f604d9fa4cc383550ba985e6ac85cd5cac7fbb%3A1576422240 Now, if I was smart I would have taken my brake calipers off to actually use this correctly but it was evident enough to me that in the region where the caliper was... there was nothing to hit suspension/guard/arm wise. So I'm going with "it'll be fine" after using the tool to hopefully very precisely measure the wheel clearance. Also while doing this, I had the very VERY bad idea of jacking one of the wheels/suspension arms up while the rest of the car was on jack stands. I did this to see how the arm would travel. This all was well and good until the car slid off the stands and went through a fence. So don't do that. Incredibly nobody was hurt and there was only minor damage to the rear bumper as the car didn't have far to slide, and had 3-4 wheels on it. The only damage turned out to be the fence itself which was easy to fix, and a little bit of damage to the fibreglass rear bumper trim. I had already planned to try a touch up paint kit to fix the time I drove into my garage door to see if it'd help in the interim before I get it fixed properly. I used the Dr Colorchip kit after looking online and seeing everyone talking about it. Yes it's made for chips and not huge broken missing pieces and I'll be 500% recommending it for stone chips after using it for stupid things like me. This took about ... 10 minutes and looking at the half assed photo the 30 second job I did on the bumper corner was almost perfect just by using the tiny little brush and painting it in. The sealact stuff to remove over-painting is really useful, so if/when I do it again I'll likely slather the touch up paint well over it and then clean it up with the cleaning solution. The wheels should arrive in a couple of weeks. I am still kinda confident after doing a stupid amount of measuring (and borrowing a set of 18x10.5+15) that they will not fit because I overlooked something, somehow and flew too close to the sun. ALSO R34 GTR guard liners do not fit on a GTT. I bought the undertray brake duct guides and had the wonderful problem of them not fitting my intake, my oil cooler and the liners themselves were even worse. Attempting to fit them won't work in general - You would have to cut them up as another poster mentioned as the bodywork is different on the GTT. At least I can try to resell them. So instead of cutting those up, I cut up my old already-cut-up GTT liners and extended them by using some PP plastic and drilling some 8mm holes for some nissan clips for the 'extra' bit. Because I was happy to cut them I was able to mount them pretty damn forward so I now have some semblance of guard liners, and the brake vents seal the bumper from the bottom. It sort-of-looks like this, to give some idea - If you look at the GTR and then the GTT this is when I realised that I needed to seriously measure as the inside of the rim area is entirely, entirely, entirely different and could not take any internet measurements for granted.   
    • If you are Ecutek tuned then these TCU tunes are anywhere from $550 to $700 usd. If you are not ECUTEK tuned, then it gets costly!    
    • Sorry to hear your HFM BM57 was faulty,  did you contact HFM I would hope they would be at least grateful for the information if there was some sort of manufacturing fault, you would hope they would be sympathetic even if your item was 2 years old if it had never been fitted. May I ask where it leaked from ?
×
×
  • Create New...