Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Have you looked at the hi octane sumps? They look like a serious bit of kit and will be what I go for when I build my motor. Some nice internal gating/baffling too

+1 for high octaine sump!! and yeah, needs a bit of cut and wleding

as far as the tomei sump baffel goes i think its either place or screw fit

yeah thats a shame matty fire takes no prisoners or no prejudices

indeed steve, hardest luck story was from the first photo. The guy who lived there lost his first house in the "white flat" fire 2 years ago. his son built the house for him so he had somewhere to live, and he's copped it again. He said to one of the guys i was working with "they sell houseboats on the murray yeah? might be time for me to buy one of them!"

Whats that thingamajig?

-D

thats a "rural padmount" ground level transformer. only uses one phase from the 11kv system (the one cable coming into the "elbow" on the left). Produces 2 phases of 240v for consumer supply. This one WAS feeding 4 houses, but only 2 were left that could be safely re-energised by generators. Note, that was closed during the fire and normal operation, so shows how much heat there would have been

Hope everyone has/or is having a good xmas,

Can anyone recommend a good place to get guards rolled? My tyres seem to like scraping the guards now...

Edited by skwiz
I need some help. I think I've got an inlet leak.

If I rev the engine up and release the throttle , it stalls. But if I take it easy it's fine :P

I'm thinking it's the inlet manifold gasket ?

Any ideas on how to be sure ?

Lose the hektik flutter.... :D

Hope everyone has/or is having a good xmas,

Can anyone recommend a good place to get guards rolled? My tyres seem to like scraping the guards now...

Luke ENR34 is the man to see for guard rolling :D

any idea on prices?

only because i am too lazy to call them.

youre far too lazy for your own good jake.

About $90 a guard, give Luke a pm first mate

what you smoking james? i want some.

bleh, $90 a guard? jesus.

its only $40 a guard for ns members.

ill have to get my guards re-rolled for the cst's, might just get all type to do it.

Edited by scandyflick

I've heard someone say that 98 Octane fuels offered by the different petrol station brands are different in their makeup, and apparently BP ultimate is the better one to use. Is this true or a load of waffle? Does it really matter if someone uses V Power or BP Ultimate or Vortex 98?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...