Jump to content
SAU Community

Recommended Posts

hahahaah so that was YOU !!!

I was swearing my head off to my mate in the car when you did that

hehehe...its all good...

Im lucky it was raining otherwise I would have yelled out at you...hahaha which would have been embarrassing if you spotted me after that :P

Haha the irony is I crossed the road just to check the car out closer. Why were you stressing was it my umbrella close to your car? If so sorry - I was very conscious of not touching the paint, it was immac - just wanted to get a closer look :(

spotted primordial 2 cars in front of me heading down Coonara Ave this morning.

Were you trying to wave at me with your rear wiper? :( hehehehe

I didnt notice you back there!

Haha.. I was trying to clear my back windscreen but the wiper blade is about as effective as using one of Bob Marleys dreadlocks!! :P

Changing the rear windscreen wiper is one of those jobs you never get around to on your car...

Haha the irony is I crossed the road just to check the car out closer. Why were you stressing was it my umbrella close to your car? If so sorry - I was very conscious of not touching the paint, it was immac - just wanted to get a closer look :dry:

if you think it was immaculate then you did need a closer look :(

if you think it was immaculate then you did need a closer look :D

haha yeah sams right..

My paint is FUUCKED....

keyed 9 times and the front bar has so many stone chips my mate refers to it as the "new look galaxy paint job"

hahahah and nah I didnt even notice your umbrella you just jumped out in front from nowhere...was a bit unexpected thats all hahahaha :kiss:

hahahah and nah I didnt even notice your umbrella you just jumped out in front from nowhere...was a bit unexpected thats all hahahaha ;)

ahh - heheheI only crossed the street when you were waiting at the lights and were waiting there till I had crossed another street. So yeah if someone jumped out in front of you that day it wasn't me.

Ahhh whatever.. Nice car :P

hahaha yeh thanks, she bought it bout 3 weeks ago... i saw u wen i was in it not long ago, i think last week, on the hume highway, i was heading towards liverpool u were going the otherway, i tried to get ur attention but u didnt realise it was me, coz of the supra lol....

hows the car man?

cars going great.... im gna sell it n buy a boat :P im loosing my license..

u know neone selln a boat dude ;) lol

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...