Jump to content
SAU Community

Recommended Posts

Bit of a newbie question, I guess but I won't learn if I don't ask :)

My understanding of understeer is when the rear wheels make a smaller arc than the fronts in a turn... and of course oversteer the opposite, when the rear wheels make a larger arc than the fronts in a turn.

I can't think of a way you would understeer in a, for example, right turn, without oversteering to the left beforehand.

Is the above correct? If not how do you understeer?

Any help would be appreciated... :D

Link to comment
https://www.sau.com.au/forums/topic/29208-understeer-question/
Share on other sites

Well think of it this way....

You approach a right hand corner at 60Kms', You slow down and start to turn your steering wheel to the right, In a neutral steer situation (no under or over steer), as you turn the steering wheel the car would follow the path of the front wheels and you would go into corner and exit normally.

With understeer, the car doesn't follow the direction of the front tyres and continues to go straight ahead or there might be a delay in turning.

From a driver's point of view, you would turn the wheel and it feels like nothing is happening because the car is still going straigh ahead.

Hope that helps, I may have just confused you more =)

the car trying to go straight ahead when u turn the steering wheel to corner, usually when entry speeds exceed the limits of tyre adhersion. mostly happens in fwd/4wd, it can b pretty scary but only happens when u r giving it to it ie dropping clutch at 5000rpm before corner in 2nd gear, in the wet it can b pretty dangerous

i'll explain it even easier.... :D

* understeer sux, oversteer rules!

* understeer puts a frown on your face, oversteer puts a smile on your dial (and

maybe some poo in your pants)

to graphically demonstrate...

this is understeer, steering wheel at full lock, car nose pointing in direction of travel before turning steering wheel:

DSC_3812.jpg

this is oversteer:

abt.jpg

...and from the reverse angle:

abj.jpg

I think the photos demonstrate it very well but from some of the comments greater explanation is needed.

Understeer is as the title suggests when the car does not turn enough thus "understeering". The front wheels have lost traction and thus the front of the car pushes through the corner and the car does not turn in. It is caused generally by too higher speed on turn in or by to much power being placed to the front wheels in a FWD or 4WD car and thus once again pushing the car through the corner. The photo of the 33 clearly shows that the front wheels are turned in hard but the car is pushing forward and not turning at the same rate as the wheels. Look at the car's track/road position. It is right out on the outside of the corner no where near correct turn in point as it has pushed through the corner as it has not turned enough. Once understeer has commenced backing off the throttle to reduce speed is the best avenue to counter this problem (taking some lock off and gentle braking can also be an option depending on the levels of understeer and the corner etc).

Oversteer as the name suggests is where the car turns to much, bringing the rear of the car to a slide turning the car on a greater angel to that which is required for the corner. As seen in the photos of the 34 the cars rear is turned pushing to the outside of the corner as the car is turning too strongly. This time it is the rear that has lost traction. Oversteer is caused by too much acceleration when exiting a corner. Backing off the throttle and applying counter steering (turning into the slide) is the best way to counter this condition.

Now if you do not understand nor feel comfortable playing around with these two areas and you drive performance cars such as the skylines I think that an advanced driving course is very much a necessity for you. Understadning and feeling comfortable when these things occur is a much for any performance car driver.

Mick.

Of course too much power on the exit of a corner will only oversteer a rwd car. If you have a fwd too much power will cause the front tyres to exceed their levels of grip. There is not enough grip in the tyres to turn the car, as you are using up some of the grip to accelerate. Something has to give - either wheel spin, or the car understeers.

That wasn't very clear. !

Basically, if you run out of grip on the steering wheels - then you cant steer anymore so the car moves in the direction of the momentum i.e. straight.

-- If you regain grip on the front wheels - back off the power/ slow down then the front end will start turning you again, then the rear may run out of grip - causing an oversteering situation.

If you run out of grip on the rear tyres the car moves with the momentum again - if you are going around a right hand corner then the rear will swing around in a clockwise direction.

-- If you regain grip on the reer wheels - back off the power then the rear end will start pushing the car foward (as they only go straight - ignoring 4ws) , then the front may run out of grip - causing an understeering situation.

To run out of grip all you need is too much power or to much speed.

More confusing? well bad luck, that the best I could do :) Go to a track day.

I dont believe backing straight off in an oversteer situation is good. If you just jump off the throttle it will cause the weight of the car to transfer to the opposite side (what you feel when the car "snaps back"), and more often than not in a RWD car with some balls will cause the car to spin. Better option is to slowly move off the throttle but always keep the car accelerating/powered and control it with the steering wheel to pull it back in line.

But thats just my opinion :)

I dont believe backing straight off in an oversteer situation is good. If you just jump off the throttle it will cause the weight of the car to transfer to the opposite side (what you feel when the car "snaps back"), and more often than not in a RWD car with some balls will cause the car to spin. Better option is to slowly move off the throttle but always keep the car accelerating/powered and control it with the steering wheel to pull it back in line.

This is very true. I should have explained this part as well.

Mick.

Or anther way to explain.

Understeer is when you see what you are about to hit :)

I think you need to be careful recommending that you don't back off when you get unexpected oversteer. While this is correct in the most technical sense, if you didn't see the oversteer coming you probably don't have the experience to catch the tail when it swings back again.

When you head out to a race track, check out the skidmarks on the exit of the corner....they are always heading back to the inside of the track....a car was oversteering, the driver kept the boot right in...and the tyres regained traction and shot them into a wall.

Probably the safest idea is Mick's original suggestion, steer into the slide and back off slowly.

I believe a lot also depends on the circumstances and how fast you are going.

If its at low speed in the wet, and you suddenly hit an oil patch or something turning at an intersection, or going around a traffic island, I would think backing off pretty smartly might be best, especially if you have an LSD and both rear wheels suddenly break traction.

On a fast sweeper in the dry at high speed, if you feel the rear starting to go a bit wide, I think you might be a bit more cautious, and just slowly ease off.

Both are an oversteer condition, but the situations are totally different.

No question that the circumstance in which the O/S comes will alter the best avenue of defence and thus action to be taken. This is why a driver must be famialiar with them to the point where he/she is comfortable to drive a car through such conditions without panicing.

Mick.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Gday Thought it was about time I started a build thread! As expected this project has snowballed into a huge financial liability, but unless you’re strong willed and responsible, it’s not a surprise. Background -  My first turbo car was an R32 GTS-4, got my full license and then totalled my Au Falcon a week later, so while trying to sell my RMZ450 dirtbike to buy another car a bloke offered to swap the R32 which at the time I felt like I was ripped off but looking back and seeing prices of those now ($40kish) it was a good deal, I didn’t know enough about these cars to appreciate what I had so sold it before the RB20 blew up. Between here and there, out of 12 cars I’ve owned the note worthy ones are a V8 Lexus SC400 (soarer), a couple of XR6 Turbos and my beloved S15 which I had for about 3 years, picked it up for $12500, repairable write off but she was fine, gun metal grey/pewter and bone stock/unmolested until I got my hands on it. Ended up spending about the value of the car and 280kw, 2 demerit points by the time I got defected and sold it for $14500 (also $40kish in today’s market, rip) Fast forward to the present day, I’m in a much better position financially and daily an MQ Triton (great cars, pipe down Ranger Bois), I cruised marketplace and car sales for a few months looking for another R32, the best deal I could find was an absolute rust bucket half finished project for $12000, until this R33 popped up in Port Macquarie for $18k - unregistered and barely running but decent shape, kept an eye on it for a few weeks and the price steadily dropped, $16k then $15k then $14k, that was the point where I was like shit someone’s gonna snatch this up! It was owned by a young bloke who had big plans but him and his missus just had a baby so smartest move financially for them but big gain for me. So 2 days later I’m towing a car trailer to pick this thing up. Roughly 2 weeks and $3500 later I’m cruising around Newcastle in my beat up R33 all smiles and dose noises! It only needed some basic shit to get it going, coil packs and air flow meter, electrical stuff and all fluids changed, 158k kms and running pretty good, nice smooth engine after oil and coolant flush - when I say coolant I mean it had been filled up with tap water, every gallery and heater element was filled with rust, 8-9 flushes later and still had brown liquid coming out but she’ll be right. The car was painted R34 Bayside Blue at some point but whether it was a cheap job or just not looked after is anyone’s guess, clear coat flaking like sausage roll.  Was rethinking my choices and contemplating life, had it up for sale for $22k - still cheaper than any registered R33 but got little interest, next minute I had an opportunity at work - 6 months overseas for good money, so that was a no brainer, fast forward again and here we are with a 50% finished project. Current Mods - 200ish KW according to butt dyno Was tuned with Apexi PowerFC EBC (old school Greddy Profec)  Stock turbo (more shaft play than a Tinder date gone right) 3inch turbo back Varex muffler  Aftermarket injectors of mystery size, Power FC showed 36% duty cycle at full boost so not behd good size Someone had good intentions but stuck with the stock R33 MAF so we had misfires at 6000rpm due to the MAF hitting 5.2V So far I’ve redone the entire interior with carpet form Car Mats Direct, new Seats and steering wheel from Autotechnica, also sound system by Autobarn (mainly Kicker) Also MCA pro comfort coil overs - Hands down best purchase yet, worlds of improvement over the tired 30yrold shocks Goals - 450kw/600hp on flex tune New paint job - Midnight Purple 2 Engine is at the shop getting rebuilt with forged rods a pistons, new valves and springs, ATI Harmonic balancer, Aeroflow 7.5L sump, rear head drain and oil restrictors as per oil control thread* and cam covers modded for larger breathers, other stuff I can’t recall of the top of my head Parts purchased and to be installed once the engine is done -  Engine loom from Wiring Specialties including these options: Haltech Nexus S3 R35 Coil pack conversion  PRP Dual Trigger kit Fan controller  Other Parts -  262 Kelford Cams Turbo - Hypergear ATR43SS3-ProS with T51R mod (whistly boi) 6 boost manifold (high mount) 50mm Turbosmart Pro gate (plumbed back for legal reasons) HKS Super Turbo Exhaust with High Flow Cat Custom 3.5inch dump and front pipe 1500cc Bosch injectors  Fuel Pump walbro 525 Haltech MAP and IAT sensors Haltech Flex Sensor Fenix Radiator with dual thermo fans LS1 Alternator Kit Oil Filter Relocation from EFI solutions and Cooling pro oil cooler Many other things sitting in my garage waiting for that engine to come back. Progress pics to follow -  
    • Losses have to be less with DC coupling. Provided the battery inverter has decent MPP tracking ability - which really shouldn't be a problem. It's not 2005 any more.
    • Hi, Will the R33 GTR rear brake backing plates fit a GTST? I'm struggling to find GTST ones but can find new GTR ones.   Thanks.
    • I also got the same floor mats for a bit of extra bazzaz haha
    • Some more close up pics now that I’m back to working on the car, the loop pile is nice but again haven’t compared it to the other types in person, it’s hard to tell from the pics on the website. View of the hemming on the edges too, it comes in 2 pieces - front and back, honestly very happy with it for anyone on the fence.  Also attached my previous pics from further up as it didn’t let me post them directly before. (Nothing worse than photo bucket pics that aren’t hosted anymore years later)
×
×
  • Create New...