Jump to content
SAU Community

Recommended Posts

I like the way you work...

Sounds a bit like mine, except I didn't even rebuild it... Just need to change a few things, then push its limits...

i tried that on the first one but the dipstick was popping out every run on 18psi and rings were stuffed, and for the cheap cost of freshening one up (i do assembly work myself) its not worth the hassle to risk putting in used shitters imho. Maybe its just my luck but the last rb30s ive had are not in ideal health compression wise.

should be interesting to see what will be first to go, id say rodbolts or rods if the tune is safe enough not to get the pistons first.

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

i tried that on the first one but the dipstick was popping out every run on 18psi and rings were stuffed, and for the cheap cost of freshening one up (i do assembly work myself) its not worth the hassle to risk putting in used shitters imho. Maybe its just my luck but the last rb30s ive had are not in ideal health compression wise.

should be interesting to see what will be first to go, id say rodbolts or rods if the tune is safe enough not to get the pistons first.

The one I have is near on perfect with compression.

Luck of the draw really. But now I appear to have either head issues or turbo issues...

And I couldn't justify more then the $660 I spent in total that got me a clutch as well.

Pistons/bearings and then paying someone to do the machine work... Not the way i treat it...

As for what'll break first... I'm trying for a piston through the block, or a bent rod at least...

  • 3 weeks later...

not much yet, I have the engine at home now. Got the exhaust manifold faced at my mates workshop, and just collecting gaskets. Does anyone have a recomendation on a Exhaust manifold gasket? I got Quoted $110 from nissan for a standard one.

Perhaps give Fabre a call and ask them for a gasket (just an aftermarket one).

I had a quick look on the net and found a permaseal exhaust mani gasket for about $35. I am sure it will do the same job.

Perhaps give Fabre a call and ask them for a gasket (just an aftermarket one).

I had a quick look on the net and found a permaseal exhaust mani gasket for about $35. I am sure it will do the same job.

I got a permaseal gasket through tweakit.net

cheap and decent quality.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...