Jump to content
SAU Community

Recommended Posts

Ok as most as most of you guys know recently i had to change my Lower Control Arm and Caster Rod, after getting a new set of tires, alignment and suspension check the car is starting to pull to the left (if I let go of the steering wheel it will just start going to the left) I was wondering what you guys think it is, it drives fine i took it to the midnight cruise with no dramas but its worrying me for the Buller cruise. Does anyone know of a good suspension specialist near Caulfield East? After a close examination I think I've tightened the LCA bolt too tight but it seems to be stuck now (It free spins, no amount of untightening or tightening makes it move) I'm currently getting another bolt from the guy I bought the LCA from but I just haven't had the time (as he lives in Frankston) although I dont think it will have a major influence on the steering will it?

Any input appreciated

EDIT: I have to keep the steering wheel slightly to the right for it to go straight

Link to comment
https://www.sau.com.au/forums/topic/294690-car-pulling-to-left/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Ok as most as most of you guys know recently i had to change my Lower Control Arm and Caster Rod, after getting a new set of tires, alignment and suspension check the car is starting to pull to the left (if I let go of the steering wheel it will just start going to the left) I was wondering what you guys think it is, it drives fine i took it to the midnight cruise with no dramas but its worrying me for the Buller cruise. Does anyone know of a good suspension specialist near Caulfield East? After a close examination I think I've tightened the LCA bolt too tight but it seems to be stuck now (It free spins, no amount of untightening or tightening makes it move) I'm currently getting another bolt from the guy I bought the LCA from but I just haven't had the time (as he lives in Frankston) although I dont think it will have a major influence on the steering will it?

Any input appreciated

EDIT: I have to keep the steering wheel slightly to the right for it to go straight

Maybe they didn't align it probably? Because if problems was with the things you install, wouldn't the car sway left when the steering wheel is straight? It's just a guess lol

But I'd hate to see you fall off the mountain next weekend :down:

its meant to veer to the left ever so slightly if you take your hands off the wheel

its a safety feature designed to make you not run onto the wrong side of the rd

just check how much - if in doubt goto a wheel balance / suspension place

Could it potentially be your tie rods? Even after an alignment, the settings won't stick if your tie rods are porked.

Suggest you get those looked at.

A nice place to go around East Caulfield; perhaps Pro Tek tyres? They're located on the corner of Ferntree Gully Rd and Dandenong rd. If not there, you can head down Nepean Hwy towards Nissan Brighton. Theres a place directly across from there but I'm not sure of the places name.

Good luck.

its meant to veer to the left ever so slightly if you take your hands off the wheel

its a safety feature designed to make you not run onto the wrong side of the rd

just check how much - if in doubt goto a wheel balance / suspension place

Actually, thats true. Because the roads are made to be on an angle, so water and stuff rolls off to the side. There's one way to test it, is to drive in the middle of the road (of course when there's no cars), then let go off the steering wheel lol.

Could it potentially be your tie rods? Even after an alignment, the settings won't stick if your tie rods are porked.

Suggest you get those looked at.

A nice place to go around East Caulfield; perhaps Pro Tek tyres? They're located on the corner of Ferntree Gully Rd and Dandenong rd. If not there, you can head down Nepean Hwy towards Nissan Brighton. Theres a place directly across from there but I'm not sure of the places name.

Good luck.

ProTek and tierods/ends.... sounds like a plan.

Will pull to the left on most roads due to the slope, if you run a little more castor on the left i think it is it drives straight on cambered roads.

also take into consideration tyre condition and inflation, make sure they are all even,

and possibly brakes dragging or handbrake being overadjusted on the left side

or even a dodgy wheel alignment, these 4wsteer systems need experienced ppl to do them right.

could be a stuffed Tie rod since you hit it hard enough to bend an LCA

did you get an alignment print out from the aligner,

as some places will just say, we made it as straight as we can, without showing any printouts with all the alignment settings

could be a stuffed Tie rod since you hit it hard enough to bend an LCA

did you get an alignment print out from the aligner,

as some places will just say, we made it as straight as we can, without showing any printouts with all the alignment settings

Yea man Nathan gave me the alignment print out but I dont know about this stuff, I'll go get it and post it up here to see if anyone know about it

Some comments the mechanic left after a comprehensive check:

Play in L/H Front King Pin

Play in L/H rear tie rod end and upper control arm joint

L/H ball joint rubber cover split

sounds pretty serious..........

2deg less castor on the left than right, 2mm less toe on left than right, 1deg less neg camber on the left. Normally when they can't adjust camber and castor atleast get the toe equal side to side... Take it somewhere that can give advice when they see the camber/castor is out that much with no adjustment IMO.

i see this as the issue. the .3 of a degree difference in camber on the rear is insignificant compared to the fronts overall differences.

yeah i agree with ryan,

all you have to do is just look at the final values column and compare left to right

The values should be very similar left to right

your front end is showing some major differences

take it to a suspension specialist and see if they can fix it using factory adjustments

otherwise, the problem lies deeper within the suspension mounting points which could have been damaged in the accident, or possibly a bent hub

Are you running standard (stock) suspension setup?

If you are - try to find the factory manual - it seems to have all the correct angles (specs) etc. and send it to the wheel/suspension place.

Then take the car for a run on the freeway.

Ok well the story is that I brought the car to ProTek where they said (after looking at the alignment sheet) that he thinks the guy wasn't exactly the most capable but in his defense he said that he thinks the whole suspension has been pushed back and in a bit, his suggestion was to bring it to pedders and get an aftermarket setup that would allow me to adjust and compensate for the damage, or to bring it to a specialist and see what they can do. He recommended me to Kents but of course every time I hear "panel beater" there is only one real name that comes to mind when operating on a budget (Vu) so the car is now with Vu @ DT Panels and hopefully he'll be able to get it fixed with no real dramas and at a good price

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...