Jump to content
SAU Community

Recommended Posts

I have a 240K C110 thats been sitting in a paddock for about 10 years. Also have a 260Z thats been there for a few years aswell...

Just wondering if it would be worth stripping and selling them. Is there a demand for parts at all?

Is the 240K a manual or auto ?,

if its a manual, I dibs the clutch / brake peddles, and the clutch slave cylinder, and the gearbox shift leaver and pin, and the floor gearstick boot

if you not wanting to much for them.

Nigel

Edited by noddle
  • 2 weeks later...
  • 2 months later...

Finally have some pictures of the car.

Unfortunately, as the pictures show, the car was smashed up by someone and a few parts stripped since it was parked. :)

The only part I want to keep are the rims. Feel free to PM me an offer for the whole car or let me know if you want to have a look at it in person.

post-4688-1266102227_thumb.jpg

post-4688-1266102290_thumb.jpg

post-4688-1266102315_thumb.jpg

post-4688-1266102336_thumb.jpg

post-4688-1266102351_thumb.jpg

Edited by Priestley
On the way home I took a backstreet in Seymour I've never been down and came across another 240K coupe shell sitting in someones yard. I took a couple of pics that I'll try and upload later today.

well look at that, the c110 gods must have blessed you :)

Edited by Dan_J
well look at that, the c110 gods must have blessed you :down:

I think the gods are telling me to restore a C110.

This one is just a shell and had front left damage. Couldn't get a really good look at it, but if anyones interested I can let you know where it is and you can have a talk to the owner.

post-4688-1267416954_thumb.jpg

post-4688-1267417086_thumb.jpg

post-4688-1267417106_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...