Jump to content
SAU Community

Rb25det Neo Modding

mattye

By mattye,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Tangles Grand Master

Tangles

Posted
Posted

A quick list of mods to be used to get up and over 250kw at the wheels

Add in labour costs, fluids, and dyno tunes

Engine: - $11,500

$30 - Ryco Z201 fuel filter, Ryco Z145 oil filter

$200 - Bosch 040 fuel pump with direct battery feed at 13.8volts

$500 - Splitfire coil packs

$20 - NGK BCPRE6 0.8mm copper v-groove spark plugs

$150 - Davies Craig automatic transmission oil cooler upgrade kit

$470 - MV Automatic valve body shift kit & auto service kit

$500 - Koyo Radiator upgrade

$150 - Greddy remote oil filter relocation kit

$20 - Fujimoto sump plug drain valve

$60 - Catch can kit

$150 - Nismo adjustable fuel pressure regulator

$250 - Nismo Z32 Air Flow Meter

$230 - 3inch JustJap stainless steel single dump pipe system

$250 - 3inch high-flow metal race cat

$300 - 3inch cat-back exhaust system with Magnaflow mid-muffler and Kakimoto GTR Racing rear-muffler

$100 - Cold Air Radiator air guide for cold air induction

$100 - Apexi power intake pod filter, using standard snorkel air feed & under body feed

$600 - Trust 600x400mm FMIC bar & plate, with custom hard pipe kit

$100 - Hard pipe intake to turbo

$100 - HKS heavy duty turbo actuator

$2500 - Garrett GT3076 700177-5015 IWBB Turbocharger, ported Nissan 45V4 front / AVO .73 rear housing

$500 - JDM S15 Silvia 450/480cc injectors

$120 - ARP head stud kit

$2000 - Ported, Flowed & Machined headwork including new valve seals, valve seats and valve guides

$200 - EPP Clear camgear timing cover

$200 - Cometic gasket kit including rocker cover, intake manifold, intake collector & exhaust gaskets

$250 - Cometic head gasket 87mm x1.2mm

$100 - Aerospeed adjustable exhaust cam gear pulley wheel

$900 - Tomei 256 intake / 256 exhaust poncam gear set

$400 - Tomei 8.8mm high lift springs

$50 - Tomei oil gallery restrictor

Suspension: - $3,500

$1300 - Bilstein front and rear suspension shocks, with ‘lowering’ circlips, using standard springs

$600 - Whiteline front and rear adjustable swaybars

$200 - Dayz adjustable engine swaybar, custom boot swaybar

$100 - Whiteline front castor kit

$100 - Whiteline rear subframe alignment kit

$1200 - Uwe Jean Ballou R32-GTR 17x9.5 inch rims with Marshal Mactrac TX tyres, 235/45/17

Brakes: - $2,000

$500 - Maltech stainless steel braided brake lines, front and rear

$400 - DBA slotted front brake discs

$100 - Cusco brake master cylinder clamp

$1000 - Panoz Outlaw 4000-series front billet aluminium 4-pot disc calipers w/ Wilwood racing pads

Interior: - $3,000

$300 - SAAS D1 Drift adjustable race seat

$200 - Flynn racing seat rail

$100 - Apexi electronic boost gauge

$200 - 3x 2" DIN gauge setup including boost pressure, oil pressure & oil temperature

$850 - AEM F/IC-8 copgyback ECU with Dell c640 latitude laptop

$350 - Greddy Profec-B spec-ii dual stage Electronic Boost Controller, set to 1.00 bar and 1.20 bar

$1000 - Toshi ecu remap, tuned by Boostworx

250rwkw for roughly $20,000 in parts, plus servicing/labour costs - search ebay for savings

kidafa Veteran

kidafa

Posted
Posted
Don't do half that crap listed above. I can not believe someone wasted their time typing all that out. :)

Well lets see your opinion on what to do then :) No including 26 conversion and a 34gtr front end cos not all of us have mega coin to blow! Does look like the hottest stag in aus imo though mate :)

I'd be doing:

3" turbo back

Split Fires (if yours are missing AT ALL)

FMIC

EBC hi at 12 psi

Pod in a box with cold air feed and $5 intake pipe mod

SAFCII and SITC or as you have a S2 get the chip put on the board

QWK32 Veteran

QWK32

Posted
Posted (edited)

Darrin is still running the RB25 Neo. To see 250rwkw and just above can be done on an unopened engine. basically what i will be running is:

- FMIC

- Ecu

- Fuel pump, not because the old one is dying but just for piece of mind

- Injectors

- Turbo upgrade, stock turbo would see 200 but not much more.

- Full 3" exhaust

- Air Filter with CAI

running a safe tune and boost level i hope to see between 220rwkw and 250rwkw. total cost for me, around the 5k mark.

Edited by QWK32
M I K E Mentor

M I K E

Posted
Posted
250rwkw for roughly $20,000 in parts, plus servicing/labour costs - search ebay for savings

alot of the stuff listed has nothing to do with the power output though, so 20k for 250rwkw is a bit silly to write

rb25's are amazing motors, you don't need to spend alot to get them to 250rwkw - you don't even need to open them!

32TAXI Experienced

32TAXI

Posted
Posted (edited)

All that my Neo is getting:

Z32 afm + plug

Apexi PFC

Blitz 525cc injectors

Greddy Fmic

Blitz Nur front pipe + cat back

HKS intake pod

Alloy radiator

HKS GTRS/2535 or similar

Bosch intank pump

Should see over 220+awkw!

Edited by RED513
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
All that my Neo is getting:

Z32 afm + plug

Apexi PFC

Blitz 525cc injectors

Greddy Fmic

Blitz Nur front pipe + cat back

HKS intake pod

Alloy radiator

HKS GTRS/2535 or similar

Bosch intank pump

Should see over 220+awkw!

Assuming that your exhaust is 3in the main ingredient is a big turbo such as GT 3076 (or even a GCG highflow) and you should get over 240awkw. You could save money by getting a nistune instead of the PFC and spending the money on the turbo! (Oh and get a boost controller instead of the radiator).
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
Darrin is still running the RB25 Neo. To see 250rwkw and just above can be done on an unopened engine. basically what i will be running is:

- FMIC

- Ecu

- Fuel pump, not because the old one is dying but just for piece of mind

- Injectors

- Turbo upgrade, stock turbo would see 200 but not much more.

- Full 3" exhaust

- Air Filter with CAI

running a safe tune and boost level i hope to see between 220rwkw and 250rwkw. total cost for me, around the 5k mark.

To get to the higher figure you may need an uprated afm.
666DAN Grand Master

666DAN

Posted
Posted
All that my Neo is getting:

Z32 afm + plug

Apexi PFC

Blitz 525cc injectors

Greddy Fmic

Blitz Nur front pipe + cat back

HKS intake pod

Alloy radiator

HKS GTRS/2535 or similar

Bosch intank pump

Should see over 220+awkw!

Sounds literally exactly the same as a Neo engine I know :) My advice though, get the GTRS instead. The 2535 is great, but you'll end up wanting more :(

Tangles Grand Master

Tangles

Posted
Posted
alot of the stuff listed has nothing to do with the power output though, so 20k for 250rwkw is a bit silly to write

rb25's are amazing motors, you don't need to spend alot to get them to 250rwkw - you don't even need to open them!

mate you can do it for 5grand

obviously my list is the whole thing, suspension,brakes,engine,electronics, 15k to 20k depending how you do it

it is a simple list & of course most parts arnt needed for power production - its not rocket science (ie braided brake lines wont net 1billionty kw)

why do I have to point that out? :(

M I K E Mentor

M I K E

Posted
Posted
mate you can do it for 5grand

obviously my list is the whole thing, suspension,brakes,engine,electronics, 15k to 20k depending how you do it

it is a simple list & of course most parts arnt needed for power production - its not rocket science (ie braided brake lines wont net 1billionty kw)

why do I have to point that out? :(

haha sif you took that as a personal dig? but if you want to get technical, you did write:

250rwkw for roughly $20,000 in parts, plus servicing/labour costs

:)

32TAXI Experienced

32TAXI

Posted
Posted
Assuming that your exhaust is 3in the main ingredient is a big turbo such as GT 3076 (or even a GCG highflow) and you should get over 240awkw. You could save money by getting a nistune instead of the PFC and spending the money on the turbo! (Oh and get a boost controller instead of the radiator).

Already got Pfc fitted and tuned, Injectors and Z32 awaiting bigger turbo!

Need a radiator as seeing 96'c and Qld summer coming up!

  • 4 years later...
RBfreak69 Newbie

RBfreak69

Posted
Posted

Hi guys, Ive got a 99 Stagea RS Four S and im wanting to start building up an engine, ive found a 25det neo with 89,000kms for $2000. Just wondering what aftermarket parts i should get, nothing too expensive.

Cheers

RBfreak69 Newbie

RBfreak69

Posted
Posted (edited)

I don't want to spend heaps, Don't really know what my budget is yet. just looking around 260kw mark atm. I wasnt meaning opening it up. Just external stuff

Edited by RBfreak69
wolverine Grand Master

wolverine

Posted
Posted

FMIC, bigger injectors (480cc),new fuel pump, bigger turbo (hiflow), engine management (Nistune), 3" turbo back exhaust would be the most basic modifications required.

You can choose, bigger and better items but that is a basic starting point.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      New R32 owner soon

      By joshuaho96 · Posted

      Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • niZmO_Man
      R32 Nostalgia

      By niZmO_Man · Posted

      From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • niZmO_Man
      New R32 owner soon

      By niZmO_Man · Posted

      Remember this is 1988 tech.
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • Duncan
      1992 R32 GT-R Race Car

      By Duncan · Posted

      heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...