Jump to content
SAU Community

Recommended Posts

Yew, i asked the misses for than xmas..

"Keep thinking tho!! At least your prices are coming down, first $700 pressies now $400, only one more try to get it right it seems :ninja:"

first one was a new snowboard.. second was the sways.. maybe i'll just get the rear sway?

Yew, i asked the misses for than xmas..

"Keep thinking tho!! At least your prices are coming down, first $700 pressies now $400, only one more try to get it right it seems :ninja: "

first one was a new snowboard.. second was the sways.. maybe i'll just get the rear sway?

what sort of snow board are you after Andrew? Remember what I sell.

Lib tech trs btx 159 2010 model

0910Lib_TRS_btx-d.jpg

wasnt sure you did libtech tho. and 550usd or so when i go there..

No we do APO... sorry

see link http://www.apo-snow.com/site/index.php

Edited by andy65b
  • 1 month later...

I thought I'd dig this thread up a little as its somewhat relevant to what I need at the moment.

Is this the BC kit that was mentioned earlier? http://justjap.com/store/product.php?produ...at=0&page=1 Im looking to get either new springs or a coilover setup for my recently purchased baby M35, however Im doing it for the opposite reason to most; my car is sitting too low for me ! Id say the front lip is about 8cm off the ground and Im making far too much contact with every day obstacles, add in to the equation that I cant even get it up my drive way and it starts to make a little sense.

Ive got a few guys here in Adelaide chasing up parts for me, but I figured some of you might have suggestions as to an easy way to get my ride height up to something closer to standard. Is a new set of coilovers going to be the easiest way to get it done or are there some 'standard' springs out there which will actually fit properly and raise it up a little?

I thought I'd dig this thread up a little as its somewhat relevant to what I need at the moment.

Is this the BC kit that was mentioned earlier? http://justjap.com/store/product.php?produ...at=0&page=1 Im looking to get either new springs or a coilover setup for my recently purchased baby M35, however Im doing it for the opposite reason to most; my car is sitting too low for me ! Id say the front lip is about 8cm off the ground and Im making far too much contact with every day obstacles, add in to the equation that I cant even get it up my drive way and it starts to make a little sense.

Ive got a few guys here in Adelaide chasing up parts for me, but I figured some of you might have suggestions as to an easy way to get my ride height up to something closer to standard. Is a new set of coilovers going to be the easiest way to get it done or are there some 'standard' springs out there which will actually fit properly and raise it up a little?

Hi Dunc, I recently fitted a set of BC BR coilovers to my Stagea, these were updated to correct some issues with the earlier designs. Most of the issues have been sorted, leaving you only having to re-use your original rear shock top mount. If you do buy, ensure that what you're buying is updated, not old stock, otherwise you'll have issues. The update is from September 09 onwards.

Regarding ride height, the BR coilovers that I bought could easily be set at factory height, as the rear springs are now longer; there were no issues fitting the fronts originally. The ride is quite nice and the finish is quite neat for the dollars you pay.

Hope this helps, Dale.

Hi Dunc, I recently fitted a set of BC BR coilovers to my Stagea, these were updated to correct some issues with the earlier designs. Most of the issues have been sorted, leaving you only having to re-use your original rear shock top mount. If you do buy, ensure that what you're buying is updated, not old stock, otherwise you'll have issues. The update is from September 09 onwards.

Regarding ride height, the BR coilovers that I bought could easily be set at factory height, as the rear springs are now longer; there were no issues fitting the fronts originally. The ride is quite nice and the finish is quite neat for the dollars you pay.

Hope this helps, Dale.

Hey Dale, Thats fantastic news - thankyou! If my mechanics aren't able to find anything I'll let the know about the BC BR's and go from there. Fingers crossed they do source something locally so I can get it done asap though ;)

  • 2 months later...
Hey Dale, Thats fantastic news - thankyou! If my mechanics aren't able to find anything I'll let the know about the BC BR's and go from there. Fingers crossed they do source something locally so I can get it done asap though :)

Did you source anything locally? I am wanting to upgrade the suspension too and Iam in Adelaide. Who is fitting the suspension for you?

Cheers

Also, which ones from JustJap to buy?

BR Type RS Series or V1 Design VS Series ?

  • 5 weeks later...
Did you source anything locally? I am wanting to upgrade the suspension too and Iam in Adelaide. Who is fitting the suspension for you?

Cheers

Also, which ones from JustJap to buy?

BR Type RS Series or V1 Design VS Series ?

I ended up puttin in V35 springs (These are the same as 350z springs), but Im still trying to work out how to get more height - my body kit just sits damn low. front and back is at ~12cm or so now, and whilst it makes a huge difference theres still a lot of stuff I cant negotiate without scraping. The BR's are the ones to go with if you're buying from teh BC range, however they wont get me any higher than stock.

I just had my local mechanics fit the suspension, its all pretty straightforward / standard :cool:

I ended up puttin in V35 springs (These are the same as 350z springs), but Im still trying to work out how to get more height - my body kit just sits damn low. front and back is at ~12cm or so now, and whilst it makes a huge difference theres still a lot of stuff I cant negotiate without scraping. The BR's are the ones to go with if you're buying from teh BC range, however they wont get me any higher than stock.

I just had my local mechanics fit the suspension, its all pretty straightforward / standard :ermm:

I have some standard AR-X springs if you need em....lol

I have some standard AR-X springs if you need em....lol

The AR-X springs should sit me up ~40mm compared to stock, yeah? If so - definitely keen to give them a whirl! :down: I'll shoot you a PM.

Edited by Dunc
The AR-X springs should sit me up ~40mm compared to stock, yeah? If so - definitely keen to give them a whirl! :P I'll shoot you a PM.

please tell me you are kidding? do you want to drive a boat?

:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...