Jump to content
SAU Community

Recommended Posts

This facade that RBR are putting on in regards to equal billing is turning fans away.

Do they believe that we are so stupid not to catch on?

RBR can go and choke on a bag of Dicks!

If it wasn't for Capt Chin having decent success, I am sure we would all just walk away from giving them any sort of support

No doubt they will be 1-2 after the race,

Hopefully MW in front.

However I will be rubbing every lucky foot and Voodoo Doll I have to see I'matool spear off into the country side.

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Yeah I didn't understand that. I started punching the couch when he qualied first. Can't stand him anymore.

Noticed Nando was taking a looong hard look at the RB6 after qualifying though. He might think theres something suss (but we all know he is prone to have a sook).

Hopefully Webber finishes first, SV and FA tangle, and Hamilton second :thumbsup:

not to side with RBR but I probably would have done the same thing given that Vettel is ahead in the championship and therefore you would try to give him the best opportunity of winning the WDC.

Of course my main gripe is that RBR did not provide the same support to Webber when he was leading the championship, by giving poor team orders in the sphincter of the universe in both the race and qualifying and using the bad strategy for Canada when clearly they should have made it Webber ahead of Vettel given their relative positions in the WDC at that time.

It's obvious to see where RBR's allegience lies, I guess Webber signed on for further years because he thinks RBR is still the best chance for a WDC win in the coming years, but he'll be saddened to find out he'll just end up like Barachello.

not to side with RBR but I probably would have done the same thing given that Vettel is ahead in the championship and therefore you would try to give him the best opportunity of winning the WDC.

Of course my main gripe is that RBR did not provide the same support to Webber when he was leading the championship, by giving poor team orders in the sphincter of the universe in both the race and qualifying and using the bad strategy for Canada when clearly they should have made it Webber ahead of Vettel given their relative positions in the WDC at that time.

It's obvious to see where RBR's allegience lies, I guess Webber signed on for further years because he thinks RBR is still the best chance for a WDC win in the coming years, but he'll be saddened to find out he'll just end up like Barachello.

Webber has been in front of Vettel, had a better quaifying record this year, has won as mang GPs as Vettel this year, there are still 10 GPs to go... Vettel being ahead on points means very little at the moment.

Earlier in the year was Helmut Marko at every GP? I recall that he used to only turn up to the occassional race and often commented from a distance about the team. Interesting to see him in the pits the last few weekends since the sphincter of the universe! ???????

Webber has been in front of Vettel, had a better quaifying record this year, has won as mang GPs as Vettel this year, there are still 10 GPs to go... Vettel being ahead on points means very little at the moment.

Earlier in the year was Helmut Marko at every GP? I recall that he used to only turn up to the occassional race and often commented from a distance about the team. Interesting to see him in the pits the last few weekends since the sphincter of the universe! ???????

If you're talking head to head Vettel leads Webber 5-4 in qualifying, I believe.

5-5 So even stevens now. So Webber was 5-4 up on Vettel

Whats the bet that if Webber is able to shadow (if) Vettel up to the first pit stop he gets no chace of jumping with either an early or later stop. They will be pulled in within a lap of one another meaning status quo

5-5 So even stevens now. So Webber was 5-4 up on Vettel

Whats the bet that if Webber is able to shadow (if) Vettel up to the first pit stop he gets no chace of jumping with either an early or later stop. They will be pulled in within a lap of one another meaning status quo

No, 5-4 includes yesterday. It was 4-all

Hang on , wires are being crossed here. Silverstone is the 10th GP of the season. So how do you have 5-4????

Bahrian: Vettel

Australia: Vettel

Malaysia: Webber

China: Vettel

Spain : Webber

Monaco: Webber

the sphincter of the universe: Webber

Canada: Webber

European GP: Vettel

Silverstone: Vettel

Hang on , wires are being crossed here. Silverstone is the 10th GP of the season. So how do you have 5-4????

Bahrian: Vettel

Australia: Vettel

Malaysia: Webber

China: Vettel

Spain : Webber

Monaco: Webber

the sphincter of the universe: Webber

Canada: Webber

European GP: Vettel

Silverstone: Vettel

I think I forgot the one where neither of them got pole

Very obvious where the RBR allegiance lies. They should have said sorry seb, yours got damaged mark kept his in good nick. there's f**k all difference anyway so just get out there and get on it.

To actually take it off one drivers car and put it on the others is showing that with only 12 points difference at the halfway point in the season they are already using any chance to give Vettel an advantage and make sure he wins WDC not Webber.

if it was 3 races to go and vettel had 20 points on his teammate then sure. but now it's just a flimsy excuse.

I'm going to tip that the first three places will be as qualified. Much as I want to see webber get up I don't think he'll be able to get around vetool

Hmmm with mark on the dirty side he'll be lucky to be third by the end of the 2nd corner, Having said that i hope mark rips that little prats wing of into turn one. :banana:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...