Jump to content
SAU Community

Size Of Hose From Boost Controller, Makes A Difference?

DriftinThruLife

By DriftinThruLife,
in Engines & Forced Induction

 Share

Recommended Posts

DriftinThruLife Enthusiast

DriftinThruLife

Posted
Posted

Hi People.

My question is, does the diameter or width of the hose which goes from the boost controller (manual) to turbo make a difference?

I have been changing some factory hoses with silicon hoses, and for this particular hose... when i took it out and looked at the inner size of the hose (the hole) it didn't exactly match up with the sizes of the silicon hoses I had.

I tried putting a smaller size (this was very tight, and I took it off just incase it would split at where I had managed to connect it) and I tried a size that was slightly larger.

When i pressed the accelerator, the boost guage seemed to react the same for the thinner or wider hose.From this I assumed it didn't really matter.

When I started the engine though...it sounded a bit different. It didn't seem to be as loud. When I took it for a drive....(well it's kinda hard to describe) but the boost guage was behaving the same (if not going up higher) but the car seemed to lag slightly?

SO BASICALLY, Does the inner diammeter/width of the hoses going in or out of the boost controller make a difference? I assume it would, as it's controlling the air pressure right? So a wider hose would have the same amount of air at less pressure?

Bare in mind I have next to zero knowledge about turbos. Thanks in advance for any help.

lachlanw Veteran

lachlanw

Posted
Posted

yeah there is probably a reason why all good boost controllers come with different sized lines . 6 mm for boost sorce and to solenoid and 4 mm for boost reference signal

PM-R33 Grand Master

PM-R33

Posted
Posted (edited)

Once the line is under pressure there is no difference. It's the difference in time it takes to pressurize that line that is important. The difference in time it takes is the amount of volume between the two sources that air has to occupy. (Think of a bigger example as intercooler piping and the turbo needing to pressurize all the piping before it gets to the intake).

For a boost controller this can mean a spike if it takes to long for the line to pressurize and then the boost controller to bleed off the air it needs. We are talking fractions of a second in such a small line. So if a line is really long or really large in diameter, it can make a difference and cause a spike that would not have occured if the line was shorter or smaller. With the diameter of most vacuum lines used for boost controllers, you aren't talking much. For example going from a 4mm hose to a 6mm hose would be the equivalent volume as say another extra 5cm in line of the 4mm hose (For example. If you want to do the calcs for the exact amount of a given length you can)

So in other words unless you are using 1/2" vacuum line for your boost controller it aint going to change sweet f**k all.

Keep your lines short is the main thing, dont have them looping half way around the engine bay and then into the car through the dash if you want your boost controller to work well.

Edited by PM-R33
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

It can make a difference. Length indeed makes a difference as well. I've seen it first hand.

Length and diameter over say 2-3 meters (seen people hide bleeders on drivers side of the engine bay) etc etc.

Being the hose gets hotter and expands more and more the larger base you start from.

Well... that's my guess anyway :)

SECURITY Grand Master

SECURITY

Posted
Posted

depends on how thick the walls are. the thicker, the better it will perform in terms of being prone to kinking and closing up on itself in vacuum. ive seen plenty of the thin walled hoses close up on themselves.

size matters boys :)

DriftinThruLife Enthusiast

DriftinThruLife

Posted
  • Author
Posted

Hmmm, you know what...I reckon I'll put up a pic of the 2 hoses side-by-side....then i'll let you decide.

SECURITY...that's a scary a** display pic you have man...wouldnt wanna meet him in a dark alley.

Lukas33....mmm that's a sexy a** display pic you have man....they wouldn't wanna meet me in a dark alley.

Lukas 33 Proficient

Lukas 33

Posted
Posted
haha sorry mate. had to.

as long as theyre short they should be no problem.

HAHAHA YES!!! i was going to point that out but thought I should keep my serious hat on. Then you went and did it :) Top work :laugh:

Yeh well after your line busting like that Phil Im surprised you didn't recommend it, Must admit though it does make you engine bay look the sex.

Yeh I have a Profec B Spec II aswell and its about 20cm from cooler pipe to solenoid. So its very short. So as long as its long enough to fit in the gap but not too long as it doesn't get pressurised/hard quick enough AND as long as it is thick enough. It should hold any load/boost without spiking nicely

Lukas 33 Proficient

Lukas 33

Posted
Posted
pussy, shoulda kept stuck into it! :ninja:

HAHAHA Stock internal 25 on 2.5 bar......harden up phil.

He is not joking about everything being braid either. He has braided electrical wiring going to the ceiling light. He has even made a steering wheel cover out of braid. Rumor has it that he has redone all the plumbing in his house with braid.

DriftinThruLife Enthusiast

DriftinThruLife

Posted
  • Author
Posted

Hmm looks like I have to change it back or get another one anyway.

It started making a high pitched whitsling noise today. And I'm guessing that's either because of a hole in it, or crack, or the plastic ties aren't tight enough but yeh....some sort of leak.

Oh well, back to the drawing board.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...