Jump to content
SAU Community

Recommended Posts

i spotted a lime green-ish R33 at the caltex around the corner from my house in kaleen thismorning on my stumble home from mooseheads. did a bit of a burnout on the way out of the servo. nice colour though

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/113/#findComment-1158827
Share on other sites

spotted that gold/yellow 33 man that looks hot i had a better look at it before it has chrome wheels but still haha looks SWOIT :(

also spotted jay.r33/staega :( i thought it was you the front looked very familiar and then i could see the little red rs4

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/113/#findComment-1158852
Share on other sites

Prolly Kate's lime green 33?

probably. i was out so late last night i caught the bus home, $1.30 instead of $20 taxi ride :D the only reason i saw it was i heard it turning on and thought "that sounds like a skyline turning on" and ran over to the servo just in time to see the car burn off. very nice colour.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/113/#findComment-1159740
Share on other sites

It was definately a skyline, had white on black ACT plates on it i think... :confused: it was a different green to the XR6-T, really shiney. almost chameleon

Just spotted Nick driving up Gininderra Drv.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/113/#findComment-1159896
Share on other sites

also spotted jay.r33/staega :) i thought it was you the front looked very familiar and then i could see the little red rs4

:)

What a day of spotting ! Usually I'm luck if I see one every few days but...

Spotted Leech going to work. We pretty much followed each other all the way from Tuggers to Civic ! Then spotted him again at about 5.45 on Erindale drive, but I don't think he saw the Volvo.. Errmm, I mean Stagea going past :)

Spotted White R33 going down Parkway in the morning too.

Then just spotted a nice gold GTiR in the tyre place at tuggers from the Syndicate club.

J

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/113/#findComment-1160069
Share on other sites

Then spotted him again at about 5.45 on Erindale drive, but I don't think he saw the Volvo.. Errmm, I mean Stagea going past  

shit sorry jay i was on the way to the g/fs i am surprised i didnt see you though :rofl: my bad i at least slowed down to let your chunky beast catch up this morning :)

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/113/#findComment-1160541
Share on other sites

White R32 GTR with black bonnet, black wheels with chrome dish on Fairbairn Ave this morning around 9am. Looked like Phil's car, but with a black bonnet. Is he back on the road?

Different Phil to Skyline performance Phil? Wine Red 32?

Id like to see this 32 your talking about.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/113/#findComment-1161138
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...