Jump to content
SAU Community

Recommended Posts

spotted a black R34GTT in Richardson running back home after i realised i didnt plug in the left front indicator

spotted him again behind me in Ashley

then spotted a blue R33 behind me with his dog and a silver R32 turning from Drakeford Drive

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/777/#findComment-6636198
Share on other sites

following a r34 gtt from kambah to the belco turn off.

Did you see the vt! wonder what happened to it!

A yellow GTT?

I saw the commodore on the parkway, looked like someone barrell rolled out of the car and it ploughed in to the ditch/bush..........

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/777/#findComment-6636935
Share on other sites

A yellow GTT?

I saw the commodore on the parkway, looked like someone barrell rolled out of the car and it ploughed in to the ditch/bush..........

LOLWUT?! Damnit, must've happened after I'd gone through. Didn't see anything :(

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/777/#findComment-6636982
Share on other sites

A yellow GTT?

I saw the commodore on the parkway, looked like someone barrell rolled out of the car and it ploughed in to the ditch/bush..........

I actually saw you as well as i was sitting at the lights next to the kambah servo.

it was after you had gone past and i think it came out of streeton drive?

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/777/#findComment-6637021
Share on other sites

Yesterday saw a custom metallic baby blue pearl looking r34 out front BDL with the boot up. Number plate was GTR### or something.

Did you notice if it was wingless? I've seen one that colour getting around without the rear spoiler.

Hmm - must find this baby blue 34 GTR. Sounds neato

If it's the one I've seen, oh god yes it is. Except for lacking a wing. Looks retarded.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/777/#findComment-6637636
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...