Jump to content
SAU Community

Recommended Posts

If you want something that is cheaper on fuel ie. runs on 91 ron or E10 and doesn't consume much,

Buy a MICRA, there's a K11 in the ACT For Sale Thread. I was seriously considering it. :yes:

The K13 the ex Mrs has is awesome to drive. Slow but awesome.

At least the Skywagon can run 91 ron and potentially uses less / km than the 33.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/897/#findComment-7124275
Share on other sites

any one know of a cheap FD rx7? thinking I might give a rotory a go,, done all the tech side of 13b turbos at C.I.T, know nothing about rb`s :(

FD's aren't all that cheap. You can find a half decent series 6 (first of the FD's) for around $15k, if you want a good one, you will have to spend the money. Like what everyone else says, rotors and fuel economy shouldn't be seen in the same sentence. I have a series 3 Rx7, with a 12a, a little bit done to it. It uses the same amount fuel as the 32 does.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/897/#findComment-7125423
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...