Jump to content
SAU Community

Recommended Posts

Hey guys!

Before I convert to to turbo, I thought Id see if anyone P platers are looking to buy a well sorted out NA.

If no interest arises, I will be seeling soon with an RB25DET

Body:

Early Model R32 GTS4 Sedan.

~107,000Km on body.

Paint on body is in very good nick.

Front bar has seen better days though.

Interior in good nick

No damage on dash

Modifications:

GTR rims

GTR Bonnet + Grill + bonnet pins (in gunmetal grey)

HSD HR Coilovers - Hight, damper and spring pre-load adj.

Adj. front strut bar - Cusco

Adj. Rear strut bar - Nismo

2Way Cusco LSD - Less than 5,000km old. Locks beautifully!

Exedy Heavy Duty clutch

3" Nismo cat back

HICAS lock bar and all HICAS lines deleted and removed

Suede Deep Dish steering wheel

Recently replaced front upper control arms

Recently replaced tie rods at the front

Recently replaced tie rod ends front and rear

Regularly servied with top shelf oils

Brand new speakers front and rear

MP3 head deck

Car will also come with:

Progressive spring and shockie setup - Damper adjustable - Great ride on the street.

GTR Box

Stock Diff (yet to confirm)

new door inserts with retrimed cream inserts

Stock suspension

Immaculate GTST bonnet (yet to confirm)

GTST Rims (yet to confirm)

Heaps more. Will add soon.

Currently has (expressions of interest for P platers)

RB25DE

~120,000km

Engine came out of Auto Stagea

Regularly serviced

Never skipped a beat, ever.

Coby headers + font pipe to cat

Also interested in selling in some time with:

RB25DET

Just over 100,000km (100,000km service done)

X-Force exhaust manifold

3" Dump pipe

Will come with (but not installed) 32 GTR cooler.

Could also sell car with a set of RE55's on 32GTR rims (half a session done) Pretty much brand new

Car will come with plates on pictures - SLO4DR (slow 4 door)

Feel free to PM me with any questions or contact me on 0403491735 (SMS if out of reception)

Interested in Trade with a drift car of some sorts with similar mods + cash swap either way.

Willing to consider:

32 GTST (4door)

33 GTST (4door)

Ceffie

S13

180SX

AE86

Located in Sydney or Bathurst.

Pics & Prices to come shortly.

Lets try

And just to change, its a Tomei Trax Advance 2 way, not Cusco.

$9000 For RB25DE Neg.

$10,000 For RB25DET Neg.

Photos Up soon

Lets try

And just to change, its a Tomei Trax Advance 2 way, not Cusco.

$9000 For RB25DE Neg.

$10,000 For RB25DET Neg.

Photos Up soon

Damn, if only you were in Vic.

Very nice car.

Just did comp test on both engines:

RB25DE:

1: 155

2: 160

3: 160

4: 155

5: 150

6: 155

(Psi)

RB25DET:

1: 150

2: 140

3: 140

4: 150

5: 145

6: 150

(Psi)

Forgot to mention also comes with N1/4Door head lights and after market blinkers.

I will wash it soon and take some photos.

Hey guys!

Thanks for all the interest, but its off the market for the mean time.

RWD 25det going in.

Attessa being stripped.

Cage going in.

more lock and back to the track it goes..

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...