Jump to content
SAU Community

Recommended Posts

My Girlfriends sister has a salon in Chelsea Heights

and have made the front half a smoothies bar, with internet cafe.

and as the weather heats, thought i'd help them out and organize a cruise. to meet at the Car wash corner of Wells road and Springvale Road. ( next to Michelangelo's)

then head 5mins down Well's Road to Thames prom.

where there is a group of shops, including a Pizza Take way :)

not dates are set as its just in the air atm, put down your interest.

dude18_smoothie_jack_400.jpg

Link to comment
https://www.sau.com.au/forums/topic/300703-smoothies-pizza-carwash/
Share on other sites

  • Replies 169
  • Created
  • Last Reply

Top Posters In This Topic

I'm here now people. not on a cruise just playing guard haha, feel free to come down if your in the area.

5/205 Thames Prom Chealsea Heights Vic 3196.

interest is looking good in the past hour's should make it this week thrusday or so

well its actually a suitable time as most people wont be working and have the next day off anyway

normally on a thursday i would be flat out and working friday to so its good for me

and im far away to cass

I won't b far away at all, I'm in melbs till later that night. Point is Christmas eve is usually still heaps busy for family things...

And there'll be masses of police out that night...

ok people.

next wednesday the 30th 630-7pm meet up at the car wash, sorry don't know the name of it, hang around for 15mins and leave at 645, get to the shops and be ordering at 7. Pizza and chicken shop next door for food :down:. Hope to see an alright turn out.

And i'll find out if im not working during the day, and if no one else is we can make it earlier.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...