Jump to content
SAU Community

Recommended Posts

I want to know...

R34 GT-T

Toyota Supra Twin Turbo (6 Speed)

Rx7 Series 6-8

Holden Monaro

and... if you know any other interesting ones??

Write em down!!

Coz i wana know what car to buy, plus its interesting for ppl :)

M14 Pulsar GTI-R = 14.05 seconds

Silvia S13 1.8 Litre = 15.08 seconds

Silvia S13 2.0 Litre = 14.30 seconds

Silvia S15 2.0 Litre = 13.80 seconds

S13 180 SX 1.8 Litre = 15.08 seconds

S13 180 SX 2.0 Litre = 14.30 seconds

U13 Bluebird Atessa SSS Turbo = 14.52 seconds

300 ZX Twin Turbo 2 Seater = 14.20 seconds

Skyline R32 GTS-T = 14.63 seconds

Skyline R32 GT-R = 12.80 seconds

Skyline R33 GT-ST-25T = 14.39 seconds

Skyline R33 GT-R = 13.30 seconds

Skyline R34 25GT-Turbo = 14.20 seconds

Skyline R34 GT-R = 12.90 seconds

Starlet GT-Turbo = 15.23 seconds

MR-2 GT-Turbo = 14.37 seconds

Supra SZ = 14.89 seconds

Supra RZ = 13.93 seconds

SC300 Coupe = 16.96 seconds

2.5 GT-Turbo = 15.06 seconds

SC400 / Soarer = 16.45 seconds

FTO GS = 17.55 seconds

FTO GR = 16.15 seconds

FTO GPX = 15.49 seconds

Familia GT-X = 15.73 seconds

  • 7 months later...
lol.. no Rx7 :( hahaha

If you want to have the fastest car and not need to do much mods except increase boost, a good tune and put exhuast nothing will beat RX7. !!!

Just a rough ride that rotary.

My mate has a series 5, he runs 10psi and the only thing that has beaten him in 7 years was a 200 grand Porsche!!

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...