Jump to content
SAU Community

Recommended Posts

hey all, im trying to find the best spraying injector around the 6-700cc/min range?

must be a single cone.

high or low impedance

siemans deka? rochester? bosch ev14 ???

any first hand experiance?

cheeres.

Injector Dynamics...they certainly have me impressed. They make a 750cc item that would suit you nicely...we recently put some 1000's in a stock GTR and the fuel delivery was spot on...afr's were rock solid at idle even with varying inlet temps.

have a good read of their website Dave and let us know what you think.

www.injectordynamics.com

Edited by DiRTgarage

I don't know exactly know what ID do to them but from what I read they are a late model higher plessure injector intended for returnless EFI systems .

The moving part inside the injector is much smaller and lighter than older types so easier to control at small and large pulse widths .

ID are supposed to got to a lot of trouble to match sets to ensure uniformity .

Google Injector Dynamic and search here under EV14 Injectors .

Cheers A .

Injector Dynamics...they certainly have me impressed. They make a 750cc item that would suit you nicely...we recently put some 1000's in a stock GTR and the fuel delivery was spot on...afr's were rock solid at idle even with varying inlet temps.

have a good read of their website Dave and let us know what you think.

www.injectordynamics.com

are these the high impedance 1000cc ? would they work with a rb25 power fc without a resistor? what psi are they rated at 1000cc

edit found this chart

post-34685-1262075268_thumb.jpg

cool. but when i can get brand new deka 4's for 40usd each its hard not to take notice. not a fan of "customised" injectors. i just dont know if there is better. spray pattern wise.

ps. does anyone know where i can find technical product sheets for these said deka 4 injectors? (60lb/hr) long series.

there not as such "customised" more matched so you shouldn't have to trim individual cylinders more that a couple of % there also batched so if you have an injector fail you can order another injector of the same batch

also they have a youtube vid of running id2000's in a NA integra there said to idle well

the twin turbo V8 boy are using them too as you can run big pressure to the injectors the 2000cc can run to 3710cc with 130psi to them

i believe they match them by the duty cycles

7000revs 80%

60%

40%

20%

6000revs 80%

60%

40%

and so on

and different voltages

exacly. im running a 12 injector setup. (2 per port shooting at each valve) rather than bashing anywhere all over the port wall.(ie stock)

havent decided whether to have them staged or running in parralell.

i got the idea from nissans new system

090714-01-01.jpg

also some sucessful race engines ie: s2 quattro pikes peak

ins3.jpg

funny. still used in the pre diesel r8 lemans cars... meaning the inlet manifold design and 2 injectors per port.. (before fsi injection)

most of the f1 turbos and most of the current wrc inline 4 rally cars. cosworth,scoda etc etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You're going to miss not worrying about rust in the strut towers like the Skyline shitboxes out there
    • A few little updates that weren't filmed due to not taking long to do or not interesting enough for their own video. My new K&N Air Filter arrived, I went with an RU-4180 which matched the dimensions of the universal cone filter the car originally had.  The battery had gone flat, while that was charging I tidied up the spaghetti wiring at the bulk head and down the sides of the engine Next job was to swap the stereo The Kenwood harness had the female ISO plugs cut off and the male ISO plugs cut off the adaptor loom and joined with bullet connectors. I ordered in a repair loom through work and re-did it all. New Kenwood unit installed (Android Auto, DAB, Bluetooth, Reverse Camera) The bonnet/hood gas struts have been poor since collecting the car. I couldn't find any suitable replacements locally so took a chance on a pair from AliExpress.  The originals don't use a retaining clip to secure the cup onto the ball fixture, would explain why I struggled for 10-15mins trying to pry off the cups. The ball fixtures unscrew using a 12mm spanner, new ones are the same size. Sadly no photo of them fitted, you're not missing much lol The dished Momo steering wheel got replaced with my Momo Tuner, turns out I ordered counter sunk bolts for the horn trim ring (like they normally are for the steering wheel) instead of allen cap (flat seat)  A terrible photo of a Quaife style gear shift knob I've had stashed in my tool box for many years after purchasing the incorrect thread size (I can see a pattern emerging with ordering incorrect parts...) Also threw in a cup holder and a (empty) Boss Coffee can, because why not  
    • GT-R clearly the better choice! The 300 is certainly not insaly fast but has a decent amount of poke. Does a nice little drift around the corners with a decent amount of throttle. It's VERY predictable in a slide too.  Feels so progressive! People probably presume there's a 25 year old driving it based on my behaviour this week! 🤣
    • Yeah Jap import. Fairlady Z then! I'm a bit the same.  They've been on my radar for a fair while but then just impulsively decided to buy one!  Was going to just buy an NA and add turbos to it later but decided to save the f'ing around and just buy the turbo version. 
    • Thanks mate, well done to you too! Yeah not looking forward to doing any major work to it!
×
×
  • Create New...