Jump to content
SAU Community

Two.06l Final Event At Compak Attak

Swiper the Fox
 Share

Recommended Posts

Marko R1 Grand Master

Marko R1

Posted
Posted
sorry guys only just got internet access...

the small crack in the block that was repaired last time engine was freshened has opened up weeping coolant out. In the interests of my own and others safety i decided not to run the car. Looking back i probably should have grouted the block as the crack is below the bottom of the welsh plugs and grouting would have stopped it.

Its very strange as when the car was rolled back on Friday no coolant was leaking out of it. A little later i jacked the front of the car up in preparation for welding a lambda sensor bung at the base of the dump pipe and coolant started to drip from the rear of the engine. We stripped the engine on Friday night and tried to repair it but on Saturday morning started leaking again. Engine is now out and ill decide tomorrow if ill just grout it or replace the block with a fresh one.

Very disapointing for all involved with the car.

As u said paul, last thing u want to do is bin it down the track with coolant on the back wheels @ 150mph.

Safety first :unsure:

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Swiper the Fox Grand Master

Swiper the Fox

Posted
  • Author
Posted
paul explained to me that the crack was repaired 5yrs ago...maybe from all of the strain the engine has undergone caused the crack to weep?

yeah have known about the crack for quite some time...has been pretty good up till now. Most 05U blocks will open up when subjected to this power level for a long period. All the bogged launches twisting and stressing the block would have done it no favours.

I grouted it this afternoon...no more weeping coolant. Was going to machine up another block but didn't want to crack a good one. Engine back in by the end of the week.

  • 2 weeks later...
  • 2 weeks later...
bigmikespec Veteran

bigmikespec

Posted
Posted

Sorry to hear about the bad news Paul, hope you get it all sorted this time mate.

In your experience, for block strength is it ok to grout as far as the welsch plugs and still use the engine for circuit work? Any coolant issues?

BezerkR32 Veteran

BezerkR32

Posted
Posted

i would not recommend it. bottom of the welsch pluds as a maximum. but run extra piston to bore clearance.

Sorry to hear about the bad news Paul, hope you get it all sorted this time mate.

In your experience, for block strength is it ok to grout as far as the welsch plugs and still use the engine for circuit work? Any coolant issues?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Marek
      Hi everyone.

      By Marek · Posted

      Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • soviet_merlin
      Ethanol Content Sensor - Always at 11%?

      By soviet_merlin · Posted

      Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...