Jump to content
SAU Community

Recommended Posts

Hey guys

I'm in the market to purchase a boost controller

there were so many to pick from :)

apexi greddy hks hdi turbosmart and a million and one others

Who uses what and who would remcomend one over another!!

•Put down what motor your using

•quick mods- high flow turbo, injectors etc

•psi your running

•and of course why you think yours in better :)

cheers!

Link to comment
https://www.sau.com.au/forums/topic/310356-boostin/
Share on other sites

Turbosmart Boost Tee, set it up inside your engine bay so you cant touch it without pulling over and popping your bonnet. Had a friend run through 3 engines because he had it in cabin and could just wind it up at any time.

Given it was a Turbo Holden V6 but still...3 engines gone.

Link to comment
https://www.sau.com.au/forums/topic/310356-boostin/#findComment-5113257
Share on other sites

+1 for turbotech manual boost controller.. never had a spike in both my RB20 and RB25.. all other electric boost controllers spiked like crazy.. turbotech uses the Spring and ball.. no bleeding of the air!

iv alwaysed used them in my drift cars there awsome. set your boost and never touch it again!

Link to comment
https://www.sau.com.au/forums/topic/310356-boostin/#findComment-5113265
Share on other sites

stock turbo you cant go past the turbotech. a spike in the midrange isnt gonna hurt the turbo, all that matters if that your boost up around 6-7000rpm isnt much more than 12psi

if you have a bigger turbo i'd recommend a profec b II, they seam a bit shitty at first and not so great to use but its very good at controlling boost

Link to comment
https://www.sau.com.au/forums/topic/310356-boostin/#findComment-5113304
Share on other sites

you could just replace the wastegate actuator with an aftermarket one and run constant higher boost if that's all you want to achieve. much safer, and undefectable.

i mean, who are we kidding, you're gonna wind up the boost, get it tuned to that boost level to make max power, and then forget about it until you get pulled over and dicked for having a boost controller that's bright pink or whatever lebo colours they come in these days.

Link to comment
https://www.sau.com.au/forums/topic/310356-boostin/#findComment-5113317
Share on other sites

I herd it's dangerous to run a manual boost tee as for boost spike :down:

Well gossip in the tea room never helped anyone.

I ran had around 10psi bleeding through a manual valve, 370rwkw/24psi... there is no issue if correctly done. That is a fact.

IMO you probably don't even need one.

Link to comment
https://www.sau.com.au/forums/topic/310356-boostin/#findComment-5113586
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I was just driving into work and while on my drive, I went to accelerate and noticed the car would sputter/hesitate and I’d hear a few pops from the exhaust before it started going faster. Then I also noticed that when I push my clutch in, the car would die. This all started happening today. Any ideas?
    • That is a lovely Volvo, just saying. Yes I should have got an 260RS when they were cheap. I do regret now.
    • ^ lots of good points made above. The thing is, "aggressive" or "flush" fitment is relative depending on how much you have been influenced by social media. My starting point is always "look at the Nismo RWD specs". That is where you should start, then start measuring as GTSBoy as sort of mentioned, because every car will be slightly different. My 8.5"+35/9.5+38 will not be "flush" enough for you because you want more "pumped" look, which is why you measure. Tyre sizes and brand/models also make a difference. Some tyres are more chunky/square, some are more rounded. That means you could get away with more aggressive offsets without rubbing. But then it also depends on your ride height. Also depends on how much your car copped damage before being shipped from Japan. So it goes back to measuring your car yourself and determining what can work. Those Nismo specs are used bacause it's a safe spec for standard car (suspension. body) with chunky tyres. But then I put 265/35 wide tyres on R34 GT-R wheels, and currently run 285/30 tyres on 18x10 wheels.
    • Sounds pretty awesome. I recommend creating a new build thread and posting all your goodness in there.
×
×
  • Create New...