Jump to content
SAU Community

Help Rb30/26 Into R33 Gtst Engine Mounts

brother_david
 Share

Recommended Posts

brother_david Rising Star

brother_david

Posted
Posted (edited)

Im just about to fit my 26/30 in the engine bay of my R33 GTST. The steel engine mount brackets i got with the block doesnt line up with the RB25 rubber mounts in the bay though :S

I feel really stupid here but anyway, it seems like the angle of the brackets is a bit to much and they just seem like they should sit closer further ack on the block :thumbsup:

Also if someone got pics of their mounts i would be glad!

/Dave

Edited by brother_david
bubba Grand Master

bubba

Posted
Posted

Use matching brackets and mounts..

It sounds like you have RB30 mounts on the block and 33gtst brackets in the engine bay.. IIRC the RB30 mounts sit the engine slightly further back than the 32/33gtst mounts.

brother_david Rising Star

brother_david

Posted
  • Author
Posted

Thanks for your help! Ye i was really fussed about what brackets to use with what mounts ;)

TiTAN> I can see you have a R33 GTS-30T in your info, so you say that i can/should use the factory R33 GTST engine bracketes and mounts?

brother_david Rising Star

brother_david

Posted
  • Author
Posted

Might have solved the problem! Im using universal rubber mounts with an offset of the bolts of about 40mm, bolted straight in. Might make a spacer for the LHS engine bracket since the engine is leaning a bit and he bolt and bolthole doesnt flat out :spank:

Anyways, the engine is in place and i can start with the exhaust manifolds!! Yeeeaaay :D

BTW, the rubber mounts costs 10 AUD/piece :)

  • 7 years later...
CenterLink Contributor

CenterLink

Posted
Posted

I know I'm pulling out an old thread but I'm doing the same. 

A rb26/30 into R33 S2. 

And was told that i need custom mounts as the rb30/26 is taller then a Rb26dett or Rb25det to it fouls the bonnet. 

 

Is this true or not. 

 

Cheers. 

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...