Jump to content
SAU Community

Recommended Posts

Curious to know how they drive. My impression is they are pretty understeery and have average gearboxes. But they are no doubt pretty quick, hatchback convenience and am curious to hear from people that haev owned and tracked them.

Not looking for the ultiate track car, but whether with some swayabr and shocks they can be pretty lively to punt around the track without oil control and cooling problems ??

Link to comment
https://www.sau.com.au/forums/topic/311840-gtir-attessa/
Share on other sites

You are correct with the understeering and average boxes standard.

My brother has one that goes very well,but now has ppg box and good suspension..as these and stock brakes are average.

They are a good little car setup properly & can be picked up very cheap now..and dont suffer the same oil problems as gtr's.

GTiR has absolutely no similarities to the ATTESA system used on the GT-R, apart from that they are in essence both 4WD. The GTR system uses a RWD setup, which when overcome by slip/torque (detected by G meters) it transfers torque to the front wheels, therefore giving 4WD. Whereas, the system used on the Bluebird and GTiR is your simple centre LSD with a 50/50 split front to rear with no electronic variation in torque split

Link to comment
https://www.sau.com.au/forums/topic/311840-gtir-attessa/#findComment-5132744
Share on other sites

Bris, the best way to get it to handle is to treat it like a FWD. Majority of the drive/steering/braking done with the front end. A big rear sway bar will remove most problems with understeer. I would resist the urge to fit a big front sway bar as it will result in more understeer. Some coilovers will also help undoubtedly.

250kw atw is not unheard of from the stock setup with boost, etc, however they do suffer from heat soak with the cooler being on top of the engine.

The stockboxes, as long as you don't treat it like a GTR it will hold up with that sort of power.

Link to comment
https://www.sau.com.au/forums/topic/311840-gtir-attessa/#findComment-5132875
Share on other sites

they are not as bad as many (who have never driven one) will have you believe.

as the guys above said their AWD system shares practically nothing with a GTR. it's basically a FWD set-up (east-west engine with FWD style box with a transfer case sending drive to the rear). they use a centre diff to apportion drive and the torque split is very close to 50/50.

the boxes are also not as bad as most will have you beleive and there are a few affordable box options if you want a better one (around $5K installed or less for a PAR or PPG).

with a rear LSD they are pretty lively, add a front and centre and even more so.

parts are pretty cheap for them, and the SR20 they have is the ducks nuts. better oil pump and oil system than most. better block. solid lifters, bigger factory cams, 440cc injectors stock, quad throttle intake, nice big turbo that is steel wheeled and plain bearing (can run 20psi no prob for around 200awkw).

get one, chuck out all the interior, get a carbon bonnet (stock one is bloody heavy), get an ARC top mount IC (don't want more weight on the nose), move battery from engine bay to the boot (any weight you can move back will help).

if you look smart you can get one of the RB models which came with very basic interior and most importantly came with a very nice close ratio gearbox and diff options (not all have the LSDs but some will have front, centre and rear mech lsds which is a big bonus), some have factory nismo cage etc too.

great little car and dirt cheap these days.

Link to comment
https://www.sau.com.au/forums/topic/311840-gtir-attessa/#findComment-5135670
Share on other sites

yeah I guess so. certainly lap time wise the evo is probably better value. BUT the GTI-R does have the novelty factor of being a bit different, and the GTI-R SR does have a great sound (unlike every other SR made, and evo's sound rubbish), and there is the fun of surprising a few people in a car most don't consider.

you're right in that for quick times on a budget it's probably not the best choice and for fun action a GTST or silvia is probably better, but for the money they are a good little thing, and one with the right bits, and a decent driver will certainly surprise a lot of people with lap times, that's for sure. :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/311840-gtir-attessa/#findComment-5135806
Share on other sites

Well this comes back to the scratched record posts i come up with every time I am at the end of a contract... If i can bump up the dollars to allow for the presently shitty exchange rate of the pound I may be off to Cambridge UK. So looking at a shopping trolley that i can belt around...the GTiR fits the bill, especially when you can have this for less then AUD5,500.

1562026-1.jpg

Buying something like this only works out tad more expensive then exporting my car and doesnt have the worry about getting it back home if i am only there for 6-12 months

There was a nice condition R32 GTSt for sale a few months ago but timing was bad. I like the hatch convenience and the fact that there does seem to be a few well maintained ones running around the UK for cheap. Right now i am going completely stir crazy working in Asia. No cars, or accessible race tracks unless your Dad/Uncle own a mine or some palm oil plantation :) Plus its too damn hot...missed out on so many opportunities because I dont have an EU visa :cool: Shits me, i have been trying to get to the UK now for 6 years, and all the work is going to Asia which is death for car enthusiasts :)

Link to comment
https://www.sau.com.au/forums/topic/311840-gtir-attessa/#findComment-5136127
Share on other sites

Wooh not see that one before Richard :) its been a while since i have even looked at a gtir.. i still love that red one from japan

thought about getting one again for a runabout they are a great little car as Richard said. having both owned them i guess we know a little more about them!

They wernt all that bad really. i had a 94 model with close ratio box in it, it went great. untill a former friend broke the box. then my oil filter spun off. ceased engine one wet foggy morning on the way to work :( (dont use normal 200sx/s15 oil filter) gtir one is a bit bigger.

otherwise i had the car for about 2 years, and it was great!

Link to comment
https://www.sau.com.au/forums/topic/311840-gtir-attessa/#findComment-5143457
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...