Jump to content
SAU Community

Recommended Posts

ok, so i went to change the plugs yesterday. had about 2 hours of light left so it was always a stupid idea, but me in my ambition just went for it.

took the cover, various hoses and electrical plugs off and started unscrewing the 8 allen key screw things holding the cover on the plugs. got to the end, and unbelievably, the last 2 had had their allen key thread stripped. so what was meant to fit to fit the key was circular.

so after spending an unjustifiable amount of time fiddling desperately with allen key and pliers, gave up, and put it back together.

spoke to a mechanic this morning who said i should use a chisel and hammer to turn it. yay, that can't go wrong at all.

so yeah, thoughts? suggestions?

thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/313301-stuffed-bolts-on-spark-plug-cover/
Share on other sites

spoke to a mechanic this morning who said i should use a chisel and hammer to turn it. yay, that can't go wrong at all.

Hammer and chisel to hammer it out!! ??? Maybe these are the only tools he can use properly.

Is the socket in the head 'completely round'? Sometime you can get away with tapping (gently) an imperial hex driver that is just slightly bigger than the metric size. By hex driver I mean one of the attachments that you find in those screw driver sets you can get. Alternatively get an imperial allen key and cut it down. The you have something to grip onto with vice grips etc.

OR

If the top of the head is raised above the plastic enough you can use a dremel with a small circular blade to cut a slot across the top of the bolt then use a flat blade screw driver to turn it out.

OR

If you are confident enough you could drill the head out so that you can remove the cover. Then you should have better access to what remains of the bolt and use vicegrips to turn it out...

Good luck with it...

thanks for the replies guys, feel a bit better about it now. was never really confident in belting a chisel in the engine bay anyways lol.

so if i drill/grind the head off, how much access will i have to the bottom of the screw?

thanks for the replies guys, feel a bit better about it now. was never really confident in belting a chisel in the engine bay anyways lol.

so if i drill/grind the head off, how much access will i have to the bottom of the screw?

little to none. u will be able to get the cover of but getting the the remainder of the bolt out of the head will be a pain in the ass.

i had the same problem with mine. dont cut anything u need an assortment of flat head screw drivers and a hammer. first try to hammer a flat head that is slightly larger than the alan key hole so that u can un screw it or if that dont work get a small flat head and get it in-between the outside of the bolt and the cover and hammer away what ur trying to do is just get the bolt to turn a little bit so that the first method i said will work.

grinding and cutting or drilling will be difficult with the bolts being at the back

ok mad082 feel free to under mind my post now :)

i had a similar issue with an allen key bolt on my boss kit recently. thread was stuffed, and the hex became rounded in my efforts to get it out.

i used one of these bits. nice an tight, or slightly too big, and hammer it in there. it should grab enough for you to unscrew the bolt.

taidan8.JPG

Edited by Munkyb0y

thanks for all the feedback guys. i got talked into trying an "easy out" screw thing. it was like a reverse drill bit. anyways, under surprisingly little drill pressure the top of the screw just sheared off the rest of the screw. And since i'd lost one i gave up and just drilled out the other one. i'll have a look at what's left on the weekend when i actually change the plugs.

not sure what i can do about the stubs, but its probably not worth bothering with.

thanks for the info, there's definitely a lot of options if this happens again

cheers

Yep do what Paul suggested and cut a slit into the head for a flathead to go in. Alternatively, weld a cheap allen key to the bolt head and turn.

I'm thinking of leaving my cover off permanently because it's a pain in the ass removing the intake everytime I want to access the coils. I'm just concerned about dust/oil collecting in there.

i ran mine without the cover on. it lets the heat escape from the coils better so they last longer. as for keeping water out, i degreased my engine with the cover on and was carefull with where i was spraying the hose not to spray around the cover as i knew water would still get in. i still managed to get enough water in there to cause a bad misfire which actually took longer to go away because when the engine heated up and started to boil away the water the steam couldn't escape very well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...