Jump to content
SAU Community

Recommended Posts

Jezzrrr - I think you'll find that once you add frieght you will be paying more. Then add the risk of getting hit with gst & customs duties (which seems to be happening far too often at the moment) & you will wish you had bought these ones. My 2c worth.

GTS500 - wish I had the cash as I would buy them off you myself...

Link to comment
https://www.sau.com.au/forums/topic/31398-hks-264-cams/#findComment-640897
Share on other sites

Go to greenline.jp or nengun and you will get new ones cheaper than these.

customs is cracking down on net tarts importing parts, you expect to pay the gst & duties that come with that. and you will pay more than is asked here.

Another thing, might be an idea to keep your coments to yaself, i dont think its appreciated when u are trying to sell something and someone goes u can get em cheaper.

Good luck with sale danny.

Link to comment
https://www.sau.com.au/forums/topic/31398-hks-264-cams/#findComment-643124
Share on other sites

Thanks to all those people with some positive imput.These cams are sold.

jezza and blabla maybey you should read the rules of these forum if you have nothing positive to say or want to buy the parts on offer,please f@#k off and get back under the rock you came from.

Link to comment
https://www.sau.com.au/forums/topic/31398-hks-264-cams/#findComment-648766
Share on other sites

Thanks to all those people with some positive imput.These cams are sold.

jezza and blabla maybey you should read the rules of these forum if you have nothing positive to say or want to buy the parts on offer,please f@#k off and get back under the rock you came from.

Perhaps you should read the rules yourself sunshine, you seem to bebreaking more of them than anyone in this thread ... LOSER.

Link to comment
https://www.sau.com.au/forums/topic/31398-hks-264-cams/#findComment-650483
Share on other sites

  • 3 months later...

I get gear over from Japan via Nengun ETC reasonable often and it is cheaper on most items ,these cams will cost you around *$800.oo landed here, duty doesnt always apply. These cams are used and you say only 3-4 hours running, were they installed and started up 'lubed " up correctly ? If so i'll offer you $700.00 only for them.

Link to comment
https://www.sau.com.au/forums/topic/31398-hks-264-cams/#findComment-847009
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...