Jump to content
SAU Community

Recommended Posts

ok this is really turning into a major pain in the ass. my previous topic (overboosting with split dump/front screamer pipe) http://www.skylinesaustralia.com/forums/Ov...23#entry5150823

so ive done the tests and listened to the people and got rid of the JJR split dump/front pipe and replaced it with the 3inch bellmouth front/dump pipe i previously had on the car which had no issues before. beleive it or not the car is sill overboosting but i dont think as bad as before.

ok so i went for a test drive, in 2nd gear by about 5500-6000rpm boost was around 18psi and then something weird happend, the car felt as if it lost a bit of power for a second then gained it back while i was watching the boost gauge the boost went down to about 16 then back up to 18 at this point i was at 7000rpm. now ive hit boost cut before (when a workshop wound my standard turbo up to 15psi instead of tuning my safc) and this definately wasnt the same power loss as when i hit boost cut bofore.

if anyone hasnt read the previous topic i made: car is running a basic highflowed turbo, full 3inch exhaust, fmic, no boost controller the wastegate is straight off the manifold pressure.

the only thing i can think of is the wastegate. when i pumped compressed air into it before it onli moved half way (and it definately wasnt fouling on the dump pipe) im assuming this is the preload on the actuator but if i loosen this off i wont be able to hold boost properly.

suggestions? cheers fellas

Link to comment
https://www.sau.com.au/forums/topic/315058-car-is-still-overboosting/
Share on other sites

what sort of ecu you running, had this problem with my high flow when i was using standard injectors and safc2, kept on wanting to go to 15 - 16 psi when i only wanted 10( i ported the wastegate hole but didnt do anything) . had to put a restriction plate in the exhaust down to 2 3/8" and this held about 11 psi. after i put in the 550cc's and power fc it went away i pulled the restriction plate and boost sat where i wanted it. i think it may have the tune (too rich) dont think the safc is good enough to control this set up

Couple of things-

The wastegate does not ever fully open to 90 degrees, yours sounds about right at 45 or so...so dont bother with that, its working....

Are you running a Full 3" exhaust with Decat pipe? Decat exhaust are a known contributor to uncontrolable boost...as the post above shows, placing a restriction in the exhaust fixed the problem...and a cat is a great restriction....especially a factory pos....

I had this issue on my last car, ADM S15, was running full 3" with Decat plus various other mods, fitted a disco (with the tight 0.64 rear hsng) to it and had major boost control issues...I fluked a fix on mine when I reconnected the factory BOV which appeared to bleed off some boost above 15psi...before I did this it seemed to wanna make unlimited boost...scary.

Best way to check whether its a wastegate size issue (which is likely the case with a Hiflow running a small internal gate) is to disconnect the actuator rod from the wastegate swing arm, move the rid to the side, drive the car, load it up through the rev range, it will be laggy as gosh darn, if it still makes 18psi like this then youre internal gate is too small and/or your exhaust is too free flowing.

I can only think it will be the wastegate actuator malfunctioning or a leak in the boost signal to the wastegate actuator. I'd replace all the signal tubing first, and if that doesnt work try a new wastegate actuator.

yeah ive got a 3inch decat pipe so the exhaust is pretty free flowing.

by signal tubing do u mean all the vac lines? ive replaced all them with aftermarket silicone stuff

and yes its standard ecu ive got an safc but its unplugged as id rather it be rich then lean. ive got an rb20 ecu with a nistune board and vct switch ready to go in the car and get tuned but i thought i should get this prob fixed before i get that tuned.

pal, how did the aftermarket ecu stop the boost from creeping?

by signal tubing do u mean all the vac lines? ive replaced all them with aftermarket silicone stuff

Yeah i mean the vac (or boost) lines. Maybe re-route your boost gauge to tee it off just before the actuator to check that the actuator is seeing full boost. Otherwise try another actuator. I have no good ideas....

Agree that ecu wouldn't be related to boost creep, but I cant explain what Pal saw on his car.

Stick the cat back in and it will fix the issue....and rob you of HP...but you dont really have much of a choice if you wanna control boost with that internally gated hiflowed turbo.....as Pal said, he put a restrictor in the exhaust and it held 11psi, not sure either where the connection is between ECU/Injectors and overboosting....

If as I mentioned above you do a very quick and simple test, disconnect the actuator rod from wastegate swing arm and drive it...if it still makes sh1tloads of boost then you need to restrict the exhaust, bleed off boost through some means or try porting the internal gate right out and put like an XR6 turbo wastegate flap in there...

This issue is very common...perhaps speak to the Turbo builder about it and the decat etc...when I was having this issue I spoke with Bill at ATS, Adam at Allan engineering in Adelaide and Kyle (6BOOST) and all suggested that the combination of a free-flowing exhaust (decat) with a small internally gated hiflowed turbo was an ideal combo to create this issue...

Edited by NSNPWR
I can see how a stock ecu could cause boost control issues, there is a bucketload of fuel and retarded ignition timing, which is halfway towards antilag.

Surely that would cause underboosting not overboosting?

rich tune =too much fuel = more burn = more exhaust gasses = more boost. need to slow down the gasses or get a good tune, that is where the restrictor plate comes in (or cat) this is widely used on 2j motors to stop overboosting.

running rich lowers EGT's so that wont cause over boosting (in fact this is why most production turbo motors run hugely rich from factory)

running lean and with retarded ignition timing will increase EGTs massivley and can cause the turbo to over boost.

which is probably why a good tune fixed any boost issues.

just tune it to suit and let the good times roll ;)

yea thats what i was thinking. im planning to run around 18psi tuned anyways so i spose if its not going over 18 im happy with that. i just didnt want to put it on the dyno and get everything tuned to only find out its boosting over 18psi.

i know i might hav to, but i dont like the idea of spending a few hundred on a cat thats gonna make my car slower :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...