Jump to content
SAU Community

Recommended Posts

Just wondered what times the quickest Stageas in oz/nz/japan were running .

Does anyone have any confirmed run times

does anyone know what the standard quarter mile is for a standard series 1 and 2??

sorry chucking another question in your post

I ran an 11.7 also in mine.

<this one. 500rwhp. There is a youtube of it running a 12.2 somewhere but wasnt running high boost. The car is in WA now so I hope the new owner (yes you Zane) takes it to the track in the middle of winter. My run was on a shit Darwin track at around 30deg.

  • 3 weeks later...
11.3 at 124.8mph mine did with 560rwhp and full weight (1740kg + driver) with 235/17 street tyres, Engine had made over 600hp previous but had spark issues so only ran on 18psi boost setting.

It will be featured in HPI magazine very very soon (next 2-3 months)

very nice !!!have any pic's?

thanks guys, the photoshoot for the mag was done ages ago so it has 33 gtr rims in the mag, maybe one pic of the LM's on it, the car now runs a totally different setup and that engine and box is in a 32 gtr. Should be interesting with the weight saving on what its capable of.

heres the actual pics of the drag run... (the other car ran a 10.6 and check out the KMH speed difference, i caught him in the top end, though he was auto and had a killer launch)

DSC_0573resize.jpg

DSC_0574resize.jpg

DSC_0575resize.jpg

DSC_0576resize.jpg

DSC_0577resize.jpg

DSC_0578resize.jpg

DSC_0580resize.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...