Jump to content
SAU Community

Recommended Posts

I have spoken to a few workshops about management and have been told OBVIOUSLY that the management they endorse is the best and everything else has faults.

One supplier in particular mentioned that WOLFs have startup issues, as in the car is hard to start. Now I am sure steve is going to answer this so here goes.

Could these startup rumours be as a result of a NON plugin wolf being installed by a person unfamiliar with wolfs which has caused this as they were inexperienced in tuning it.

Or can you expect this with a plugin wolf or any wolf for that matter. It seems a fairly significant issue so thats why I am leaning toward my first opinion to do with inexperience.

someone post up any feedback you have heard. NOT WHO YOU HEARD IT FROM

Thanks

Oh and if I take 2 wolfs is it any cheaper.

or maybe if others are looking to do this and have questions about it you could post up.

Link to comment
https://www.sau.com.au/forums/topic/31834-wolf-plugin-question/
Share on other sites

I have a friend who had a wolf plug-in. He was commenting that it does take longer to start (cranking time) but I personally think with a bit more time tuning, it should be better.

I have spoken to a few workshops about management and have been told OBVIOUSLY that the management they endorse is the best and everything else has faults.  

 

One supplier in particular mentioned that WOLFs have startup issues, as in the car is hard to start. Now I am sure steve is going to answer this so here goes.  

 

Could these startup rumours be as a result of a NON plugin wolf being installed by a person unfamiliar with wolfs which has caused this as they were inexperienced in tuning it.  

 

Or can you expect this with a plugin wolf or any wolf for that matter. It seems a fairly significant issue so thats why I am leaning toward my first opinion to do with inexperience.  

 

someone post up any feedback you have heard. NOT WHO YOU HEARD IT FROM

 

 

Thanks

 

Oh and if I take 2 wolfs is it any cheaper.  

or maybe if others are looking to do this and have questions about it you could post up.

you'll find that with any after market ecu the tuning will show how well it starts idles runs etc, my experiences all be it minimal with the old v3's showed they wern't the best with cold starts, the v4 seems to be a lot better at it, but ive not actually been in a car running one as yet so i can't comment..

I had a few issues with cold starts and re-starting on my wolf3d v4 but its all been sorted now with a software update from wolf done by steve. I have noticed it does take a little more to turn over and start but since the update its started everytime firsttime and without having to give it any gas. For the money the wolf3d is hard to go past but with the soaring aussie dollar the powerfc is getting cheaper either one will do the job for a street car.

Steve's home computer is down at the moment, so if you don't mind I'll field this question on his behalf.

Cold start is fully tunable on the Wolf, and as such if you have a Wolf put into your car and leave it overnight with Steve then he'll have no worries in making it start well in the morning.

There has been one other issue, that a few people including Rob77 experienced, where the cranking signal wasn't being picked up first time, which meant a few cranks before the car fired into life, Wolf have since released an update which makes it start first time. This was only apparent in a couple cars but Wolf quickly worked to fix the problem.

Any of the other good ECU's should be able to coldstart without any issues, just really depends on the tuner.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...