Jump to content
SAU Community

Recommended Posts

Hey guys,

Still tearing down this RB25DET I picked up this week. My next challenge: removing the crank pulley. There's no flywheel on the motor so I can't really shove anything thru the ring gear to hold the crank in place.

So my questions.....

a) what's the thread diameter of the studs that mount the flywheel to the crank? in case I need to frankenstein something up to keep it steady.

b) Am I missing anything with removing that 27mm bolt, other than giving it a good smack with a hammer to crack the seal then just undoing it with the help of a breaker bar etc?

c) Anybody have an ingenious way of securing the other end of the crank, other than by my Frankenstein method above (metal bar with a few holes drilled in to secure it against the crank, then lock it against engine stand)

Thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/319657-removing-crank-pulley-bolt-27mm/
Share on other sites

be careful man or you could damage the seal behind the crank.

put the flywheel on then use the bolts where the clutch attaches to the flywheel to tie some shit to the engine with

then yea breaker bar..

There's the problem tho - I don't have a flywheel, at all.

Thanks for the warning about the crank seal.

*Might* get access to one of those - would it be enough by itself to just crack the bolt straight off? I.e. does an air-powered tool deliver enough force to just break the bolt without needing to secure the other end etc?

yep...did it twice yesterday with RB26 engines...they were 350ft/lb tensioned. I do have a good rattle gun though but most reasonable quality ones should be enough for a 25.

The engine should provide enough resistance for the impact of the gun to loosen the bolt.

Thanks, THAT'S what I was trying to say :-)

OK, well the missus' old man has an air compressor, so I guess I need to hit up Kennard's for a rattle gun.... I wonder if they hire them out?

Thanks for the advice guys.

If no rattle gun, take the sump off and use rag covered spanner or such to wedge between the crank and block. (use a counterweight)

Great idea - I have a Bag O' Rags and a big-ass spanner. I'll try that before going for a rattle gun - I'll set the wrench up and smack it with my breaker bar.

If no rattle gun, take the sump off and use rag covered spanner or such to wedge between the crank and block. (use a counterweight)

ahh yes...before i had a rattler i used the wooden handle of an engineers hammer to wedge the counterweight.

yeah wood is the go try not to use anything thats hardened just in case it slips and centre punches something useful :P

the handle of the hammer i mentioned looks like a crocodile has been munching on it...lol

the handle of the hammer i mentioned looks like a crocodile has been munching on it...lol

I got the bastard off.

I wedged a piece of wood between the girdle and one of the rod caps at the point where the rod has minimum clearance from the girdle. Then with the timing belt still in place, I was able to undo the intake cam gear bolt and then the crank bolt with surprisingly little force... they didn't just come right off, but instead of the epic battle I was prepared for, I just had to use a measured amount of force with the breaker bar until they came free. Then used a pulley puller to get the harmonic balancer off, and that was that. It's amazing how easy it can be with the right tools (and good advice!). Thanks guys.

Head came off tonight, tomorrow I break apart the bottom end and see what the bearings look like.... :blush:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 2001 BE5D Subaru Legacy B4 RSK (3rd gen) EJ208 (pink injector) Twin Turbo 280PS 5-speed manual Full time 4WD "RSK" grade which means all of the above LQC option which means stock rear spoiler  I got it primarily to export to someone outside Japan who was interested. These BE5 Legacy B4 RSKs are going through a bit of a resurgence right know in Japan as they are one of the few cars from the "turbo, manual, RWD/4WD, 280hp gentleman's agreement era" cars that don't require stupid money to purchase. Which for some people might be a good opportunity to get as a base for restoration. If I can't find anyone to purchase it I will certainly be doing that myself over the long term. Why? Because it's properly fast in stock form, handles well enough for a GT sedan, there's still enough aftermarket and (if you can wait a while) genuine part support to make it a restoration candidate (<-- that will only get worse over time so it's a case of do it now or choose get a BL5 4th Gen). Mechanically it's fine, has only 89,200kms on the odometer. The problem with this car is that the body and exterior trims are weathered from at least the last 10 years being parked outdoors. I'm the 3rd owner, the first owner was the one that had it for 14 years and barely drove it, had a low-speed front impact (which didn't damage anything behind the radiator support) and got it fixed and sold it. The 2nd owner put most of the kms on it and parked it outside for the last 10 years, hence the door rubbers have seen better days but if you overlook those cosmetic details, it presents pretty nicely. There is some minor rust on the LH rear wheel arch which I'll have looked at too at some stage.  Also as you'd expect from a car this age, the clear top coat is gone, leaving a satin finish on the roof.  Mechanically it's fine (as you would expect from a car with less than 100K kms) but the steering does feel slightly vague around the centre position at higher speeds. So first on the list is to get the steering rack bushes looked at. There's also the Lock button on the remote which doesn't work, but the Open button does.... it means that the anti-theft system thinks it's always open? It seems like if you open the car and don't start the engine within 3 mins or so the anti-theft kicks in again without any beeps or signals. So if you got to start it after that, it won't. You have to push the open button again. That's how I understand it anyway. Just a small irritation but not a big problem to sort out. There's only one mod, the Wangan SPL muffler. Just a tad louder than stock. It's a really good mod for those who don't want to wake the neighbours but still want to hear a more prominent unequal length header EJ20 sound. Anyway I hope to get all those things done eventually, that is unless someone wanted to import it to their country from Japan (where I live). I'm open for negotiations as I really would like a Skyline... but this will definitely suffice in the meantime 🙂 *Disclaimer: This is how I picked it up from the dealer, minus the stuff on the back seat. I haven't cleaned the engine bay or done a thorough exterior clean, aside from spray painting the wipers. 
    • Wow, even with the Audi logo centre caps. I love OEM wheel mismatches. 
    • Welcome!  Can't go wrong with a Stag.
    • Looks good. Nice height.
    • Hey all, a little help from the Stagea hive mind plz.. I'm days away from buying either a 2002 Stagea 250tRS AR-X Four, premium leather, power seats and all the old switches etc that go with it, or a 2002 Stagea 250tRS VR-X Four AERO, pov pack, cloth seats etc, with coil overs, sports zorst, comes with original zorst and suspension and parts. (I think I've got the models right?) Both are VQ25DET, have 160000kms, both straight no rust both with $2000+ in recent servicing receipts, both ride on aftermarket 18" rims. The Aero has a replaced turbo as well. I like the cool factor of the Aero car but the AR-X has never been modified. Neither have been driven hardly at all in the last 5 years. Any thoughts on which one or does it come down to personal preference? davemoto 
×
×
  • Create New...