Jump to content
SAU Community

Recommended Posts

My port looks like that, but I don't have the cable. Nor the 'BOSE for Skyline' badge, even thought I have the BOSE stereo (SP model).

Mines all Infiniti badging anyway.

BTW am in touch with a company in NZ that makes the band expanders - only $30 NZ delivered for very high quality ones.

Still need to work this out: 'Also I would need to know what type of antenna plug is in the back of the radio unit eg. A single plug or a twin pin plug as these model vehicles varied."

Anyone know?

There are quite a few band expanders available here in NZ, quite a few advertised on TradeMe also

Before you order one check what Mhz you require, they generally come in two different Mhz ranges and you will need to decide which is appropriate for the FM signal range that you use

Very easy to install for most cars, except for Nissan and those damn aerial plugs they have. TradeMe also usually has adaptors for the Nissan aerials listed

Hi David,

Thank you for your enquiry. What area are you in Australia so I can

work out the frequency range you would need and also are the main stations

you listen to in the higher band range eg.over 100MHz? Also I would need to

know what type of antenna plug is in the back of the radio unit eg. A single

plug or a twin pin plug as these model vehicles varied.

Regards,

Peter

Hi Peter,

I'm in Melbourne. I like to listen to as high as 107.5Mhz and as low

as 89.9Mhz (or perhaps a little lower).

Is there an easy way for me to determine the antenna plug?

How much are the units + shipping?

Regards,

David.

Hi David,

The unit you need is a 10MHz which will allow reception below 100MHz

by deducted 10MHz from the station you want and 20MHz deduction for stations

above 100MHz. The cost is NZ$30.00 including airpostage.

There is no easy way. If the radio is a factory unit then it will probably

have a twin plug as they have a diverse antenna. If it has had the Bose

system installed instead of the factory unit then it will more than likely

have a single plug.That's as close as I can tell you.

Payment per Visa/Mastercard or PayPal or Bank Direct credit if you can do

that from Australia.

Regards,

Peter

Peter Brixton

fmBand Expanders

PO.Box 981

Christchurch 8011

New Zealand

Ph.+64 3 3666379

Fax.+64 3 3656197

Mobile.+6421356219

E Mail: [email protected]

Web.www.fmband-expanders.co.nz

  • 3 weeks later...

Hmmm... don't suppose you took a photo? Did you order one from fmBand Expanders in NZ?

I'm going to have a Tom Tom (Mini USB) plug wired in too while I'm at it.

If I CBF'd I was going to investigate having a mini SD set top box powered and connected up to the AUX. Unsure how the reception would be though with little/no aerial.

Hey - is your V36 manual? If so Geoff told me about yours.

I'm in Hobart regularly on business. If you ever come down this way let me know. Would love to bring my one over on the ferry but don't know if I could be bothered with the 10+ hour trip.

Edited by Haxorz

Hey, yeah it's a six sp. Didn't take a pic, spat it when it didn't fit and just left it. Got it from Leading Edge.

What do you do for a crust that brings you to Hobart?

Boat trip isn't that bad, I've done over half a dozen times (not much on flying).

  • 11 months later...

It's comforting to know the AFS OFF flashing indicator was because of the HID's being removed. That was my theory but considering I saw a little movement from my headlights before it would start flashing, I wasn't too sure what to think. I'm guessing the motorised assembly is getting jammed on something so to avoid burning anything out, it then switches it off.

I've left my AFS switch in the off position until I refit my HIDs on my next day off (and hopefully dry weather).

  • 1 year later...

Hey guys, ipod connector, from japan so this should work on our cars

Found the part looking through Electronic Parts Catalog for CKV36

http://nissan.epc-data.com/skyline_coupe/ckv36/7299-vq37vhr/misc/

83208-9925 ->

Edited by Mclarenmercman

How can you say its an ipod cable? there are no pic ref for that part number, i reckon they are for the different phones they have in japan, none compatible in Aus probably...

Hey guys, ipod connector, from japan so this should work on our cars

Found the part looking through Electronic Parts Catalog for CKV36

http://nissan.epc-data.com/skyline_coupe/ckv36/7299-vq37vhr/misc/

83208-9925 ->

  • 1 year later...

I would like to write a conclusion for this thread.

1. Both headlights move with steering

2. AFS function is fully restored when you revert back to D2S hid

3. Light emission 'pattern' is back when you revert back to D2S hid.

Adr compliance is stupid. Nissan design its headlight to run oem hid. People here switch it out to standard halogen globe, predominantly H1 size in which has different focal length. Then what you get is NO LIGHT THROUGH THE CENTRE OF YOUR VISION, short visible distance and your AFS malfunctions. Dangerous?? But the adr wants it that way...go figure!

Fortunately if the workshop who did the compliance are smart and proper, buy the D2S hid globe and it only takes 30mins to revert back to hid. At least it was on my 08 V36

Adr compliance is stupid.

Of course. They're trying to follow the UK one I think, with the washers etc. That's great for apline regions, don't need it in Aus. Either way, if it works for the Japanese, why can't it work for us?

Oh that's right, 50% of the cars on the road have the headlights pointed too high. Literally nothing can be done about that, even if you put adjusters in as standard (which is the case in Europe).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
×
×
  • Create New...