Jump to content
SAU Community

Recommended Posts

My R34's has been using way too much petrol lately, I get about 200km's for $50, that's close to 17L per 100km. I cleaned the K&N air filter, tried both Shell V-Power and Mobil 98 Octane, but it didn't help.

Would anyone have any idea what the problem could be? I'm thinking it might be the spark plugs, I got the premium one's put in about 30.000k's ago and haven't changed them in a while. I change the oil, fuel filter & oil filter regularly.

Thanks for the help.

check O2 sensor between the extractor and firewall. or get nissan consult and read the R34 service manual. the manuals basically covers the whole problems. PM me if u need the R34 manual copy.

the first question has to be asked, how do you drive and what mods do you have? that can rule out pretty much all other things depending on the answer.

if you have mods like a bigger turbo, etc then you will always use more fuel if you like to give it the beans often.

also if you just drive lots of short trips and spend a fair bit of time with your foot down on boost. if you do like to boost it often then you aren't too far out of the range of what you can expect, however if you do lots of steady driving and don't spend much time in traffic slowing down and speeding up then that is a bit high and the o2 sensor is probably the main cause. this can be done with a multimeter. do a search to find out how.

how long does the car take to warm up (for the needle to come up to half way)? it should come up to temp within about 5 mins of driving (or 3 or 4kms). if it is taking much longer to do this then your thermostat needs replacing and that will get you better economy because you won't be on cold start enrichment so much. coming into the colder months this can become more of an issue as you can actually get to a point where the car pretty much never warms up so you use much more fuel.

the first question has to be asked, how do you drive and what mods do you have? that can rule out pretty much all other things depending on the answer.

if you have mods like a bigger turbo, etc then you will always use more fuel if you like to give it the beans often.

also if you just drive lots of short trips and spend a fair bit of time with your foot down on boost. if you do like to boost it often then you aren't too far out of the range of what you can expect, however if you do lots of steady driving and don't spend much time in traffic slowing down and speeding up then that is a bit high and the o2 sensor is probably the main cause. this can be done with a multimeter. do a search to find out how.

how long does the car take to warm up (for the needle to come up to half way)? it should come up to temp within about 5 mins of driving (or 3 or 4kms). if it is taking much longer to do this then your thermostat needs replacing and that will get you better economy because you won't be on cold start enrichment so much. coming into the colder months this can become more of an issue as you can actually get to a point where the car pretty much never warms up so you use much more fuel.

I imagine he doesn't hit boost very often...

Thanks for the replies guys.

mad082, I don't hit the boost often since the car is non-turbo :D but thank you for the reply, I usually shift the gears around 2.5k's RPM's, I don't really drive hard.

I found a thread on how to test the O2 sensor with the paperclip method, so I will do this on the weekend. Only mods I have on the car is an exhaust system and splitfire coilpacks, I'll test the o2 sensor on the weekend, if that's fine, then I will try changing the coilpacks.

  • 1 month later...

Well I changed the o2 sensor, no improvement.

Checked spark plugs and the fuel regulator, all good.

Checked the ECU for error codes but it comes up as code 55 = no error.

I get about 320k's per full tank before the fuel light comes on.

Anybody got any other ideas with what's causing this? Bad injectors? Vacuum leak?

Fatter tires = more drag

Underinflated tires

Check for dragging brakes. Also check the park brake/handbrake.

Get your wheels re-aligned.

If your car is a manual - check for a slipping clutch

If your car is an auto get the automatic serviced.

Check the vacum line to the variable length intake manifold's acuator. This can cause the car to act sluggish at low RPMs and also lower the engine torque - therefore you will be pressing the accelerator more.

Ensure you are using light weight engine oil nothing heavier than 40 weight.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The alloy coolant reservoir has a sight glass, so as long as I can see coolant in the sight glass it's GTG, as for PS, it isn't anything catastrophic if it gets low, and as it hasn't lost a drop since I have owned the car I cannot see it being an issue, even after putting the "big block" 2.5 in....LOL The only time it gets slightly messy is at oil changes, as the oil filter sits above the frame, and I need to use a plastic bottle with its bottom cut off to catch the flow when loosening the filter
    • Good on you for taking on the job, but it is a big one. Even if you have bolt on manifold and turbo, you will need: Post throttle pressure source to boost controller to wastegate (and FPR, and ECU/MAP sensor) Pre throttle pressure source to top of BOV(s) Oil feed - you can take that from the standard port in the middle of the block Oil return to block under the turbo - this is much trickier than it seems to route a decent/wide pipe past the manifold. You really can't use rubber hose because it is way too hot there, and also the oil out of the turbo core is a bit frothy so it needs to have a decent diameter Water feed - you can take that from the standard port in the rear of the block. Water return - mine runs to a T into the heater box return, just make sure you don't create a high point making bleeding hard. All of those lines should use 200 series style teflon braided hose with heat shielding because everything needs to be routed past the manifold. Also a turbo beanie is a really good idea to minimise the chance of the car catching fire (under bonnet lining in particular) You also need to decide a cam cover breathing solution as well, will you vent externally via a catch can (probably illegal) or return to the intake (plumbing required and can oil up everything over time) Keep in mind the intake and exhaust piping in the engine bay will be custom so you either need to be able to fab ally and steel or have someone you can get a car that isn't running to. Get the wideband fitting welded into the dump pipe at the same time. Also, just my opinion, a screamer pipe attracts attention and doesn't add power, I'd plumb it back if you want to be allowed to keep the car on the road. BTW do you know anything about how healthy the motor is, and what power you are targeting? Doubling or tripling the factory power on an unknown motor is a little risky. Also fuel system will need some attention (pumps, high current hanger, direct power and earth feed, injectors etc)
    • Wrinkle black will be a thing for both
    • As I wait for parts to be delivered, I have managed to procure via a contact a R32 Nistune ECU......for now I just want to monitor what the car is doing but eventually.......who knows where we go 😂
    • To back this up, I'm always looking on the outside, seeing the level, and then opening it up anyway, as I'm worried the level I've looked at, is more so a scunge line. Then you end up dipping your damn finger in it too depending on the type of tank you're looking at just to make sure I'm not going insane.   PS, Mark, polish up the none moroso one a bit and then give it a clear coat. The Moroso one looks to be way shiner (not mirror polished, just shinier) and it'll still look weird with the two different alloys beside each other. Either that, or Id probably paint them a flat black...
×
×
  • Create New...